Operation Guide 5081
2
T
1. In the Stopwatch Mode, make sure the stopw
stopped and reset to all zeros
• If you need to reset the stopwA.
2. Hold down A for about three seconds until the w
beeps, DIST (
) appears in the lower right displa
and the left digit of the current distance value setting
flashes in the lower left displa
• This is the distance value setting mode
3. Press C to move the flashing between the v
the left side and right side of the distance value digit
decimal point.
4.
use D (+) and B (–) to change it.
• Y
99.9.
5.A
to exit the setting mode
l
l
l
l
l
l
l
l
l
l
l
l
l
How speed is indicated
• While an elapsed time measurement operation is being
performed in the Stopwatch Mode, the w
a speed value
distance you specified and the elapsed time
is indicated by the upper right dial, two indicators (1000
and MACH), and the speed hand.
• The upper right dial indicates the 100s digit value.
• 1000 appears when the speed exceeds 1,000.
• MACH appears when the speed e
• The speed hand indicates speed values less than 100.
Only ev
Example:
At a speed of 1,740, the upper right dial indicates 1000
and MACH is displa
The upper right dial indicates 700.
The speed hand indicates 40.
• Speed can be indicated from 0 to 1998.O is
indicated by the speed hand when the speed e
1998.
Speed hand
Upper
right dial
OVER
Mach (MACH)
Speed (1000)
Time Measurement
Y
stopwatch operation.
• If you want to measure total elapsed time
T
1. In the Stopwatch Mode, make sure the stopwatch is stopped and reset to all z
• Make sure that
LAP (lap times) or SPL (split times) is shown in the low
display
• If you need to reset the stopwA.
2. Press A to toggle between
LAP
(lap times) and
SPL
(split times) in the lower right
display
▲
▲
A
Elapsed Time
Use the following procedure to measure elapsed time
time readings.
T
Select split time (
SPL
) measurement and then perform the following b
D Start ➝ D Stop ➝ A Reset
• If you hav
upper right dial and speed hand will indicate the ovD to
stop the elapsed time operation.
• After pressing D to stop an elapsed time operation, you could press D again to
restart from the point where you left off.
Lap Time
A lap time reading shows the time elapsed since the last
lap time reading was taken.
• If you want the watch to calculate the speed of each lap
(when all of the laps are the same distance), specify the
lap distance for the distance setting.
• If you want the watch to calculate the speed of the entire
race, specify the race distance f
speed will be indicated each time you tak
reading, but these lap speeds will not indicate actual
speed of the entire race.
T
1. In the Stopwatch Mode, make sure the stopwatch is stopped and reset to all z
• If you need to reset the stopwA.
2. Make sure that
LAP
(lap times) is shown in the lower right displa
• If
SPL
(split times) is displayed, press A to toggle it to
LAP
.
Lap time
T
Select lap time (
LAP
) measurement and then perform the
following b
D Start ➝ A Lap* ➝ A Lap* ➝
D Stop ➝ A Reset
* The lap time is released automatically in about 12
seconds.
• YA to take lap readings as many times as
you like
display
• A lap number ( #01 through #99) alternates with the lap
hour value in the lo
reading is displa
readings, the lap number will restart from #00 follo
lap #99 .
• Pressing D to stop elapsed time measurement displays
the time (and speed if a distance is specified) of the final
lap.
Lap number
Speed
(calculated)
Minutes
Seconds
LAP
indicator
1/1000
seconds
Split Time
A split time reading shows the time elapsed since the
beginning of the current time measurement.
• If you want the w
specify the race distance for the distance setting.
• For split time readings
distance only
each time you take a split reading, the
the total race distance, and so they will not indicate
actual intermediate split speeds.
T
1. In the Stopwatch Mode, make sure the stopw
• If you need to reset the stopwA.
2. Make sure that
SPL
(split times) is shown in the low
• If
LAP
(lap times) is displayA to toggle it to
SPL
.
Split time
T
Select split time (
SPL
) measurement and then perform
the follo
D Start ➝ A Split ➝ A Split Release* ➝
D Stop ➝ A Reset
* The split time is released automatically if y
press A within about 12 seconds.
• YA to take split readings as many times
as you like.
reading is display
• The stopwatch contin
internally while a split time reading is displayed.
Pressing A to release the split will switch the lo
display to the elapsed time measurement, or y
could press D to stop elapsed time measurement
instead.
• Pressing D to stop elapsed time measurement displa
the time (and speed if a distance is specified) of the final
split (which is the overall elapsed time).
Hour
1/1000
seconds
Minutes
Seconds
Speed (calculated)
SPLIT indicator
T
Elapsed Time
Lap Time
Split Time
D
Start Stop Reset
D
➤ ➤
A
D
Start
(
SPL
display
Split Split release Stop
A
D
A
➤ ➤ ➤
Reset
A
➤
D
Start
(
LAP
display
Lap
(Lap01)
Stop Reset
D
A
A
➤ ➤ ➤
A
➤
Lap
(Lap02)
Countdown Timer
Y
of one minute to 24 hours.
countdown reaches zero
• Y
restarts the countdown from the original value you set
whenever z
• All of the operations in this section are perf
Countdown
C.
Seconds
Auto-repeat off
Start time
(Hours
Minutes)
T
Press D while in the Countdown
• When the end of the countdown is reached, the alarm will sound for 10 seconds or
until you stop it by pressing any b
• The countdown time is reset to its starting value automatically after the alarm stops
if auto-repeat is turned off.
• When auto-repeat is turned on, the countdown will restart automatically without
pausing when it reaches zero
• The countdown timer measurement oper
Countdown Timer Mode.
• Press D while a countdown oper
Press D again to resume the countdown.
• TD ), and
then press A .
T
1. While the countdown start time is on the display in the
Countdown A for about three
seconds until the hour setting of the countdown start
time star
• If the countdown start time is not display
procedure under “T
display it.
2. Press C to mov
below
Start Time
(Minutes)
Auto-Repeat
On/Off
Start Time
(Hours)
3. Perf
on the display
• While the start time setting is flashing, use D (+) and B (–) to change it.
• While the auto-repeat on/off setting is flashing on the displa
D
to toggle
auto-repeat on (
) and off ( ).
Start time
(Hours
Minutes)
Auto-repeat on
4. Press A to exit the setting mode.
• The auto-repeat on (
) is displayed on the Countdo
this function is turned on.
