Bedienungsanleitung Casio 5240 (Seite 4 von 9) (Englisch)

607041

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

Operation Guide 5240

E-39

Conﬁ guring Current Time and Day Settings Manually

You can conﬁ gure current time and day settings manually when the watch is unable to

receive a time calibration signal.

To change the current time setting manually

Pull out the crown.1.

This will cause the x

Second Hand to move to the

city code of the currently selected Home City.

If you do not perform any operation with the crown

for about two minutes after pulling it out, crown

operations will become disabled and the hand will

not move if you rotate the crown. If this happens,

push the crown back in and then pull it out again.



TYO (TOKYO)

E-38

Hold down 2. A for about one second to cycle through the

summer time settings as shown below.

AT (AUTO) STD DST

After the setting is way you want, push the crown back in.3.

E-37

To switch between standard time and summer time manually

Perform steps 1 and 2 under “To conﬁ gure Home City settings” (page E-34).1.

Selecting a city code will cause the

Hour Hand,

Minute Hand, and

Upper Dial Hand to move automatically to the current time for the selected

city code.

If you will use the watch in a city that is not included in the city code list, select a

city code that is in the same time zone as your city.

Displaying the Home City Settings screen will cause the

Lower Dial Hand to

move to AT (auto switching), STD (standard time), or DST (daylight saving time).

AT (AUTO)

The watch automatically switches between standard time and daylight

saving time in accordance with its calendar.

STD The watch always shows standard time.

DST The watch always shows daylight saving time.

E-36

STD/DST Switching

You can select summer time or standard time independently for each city. The initial

default setting for all cities is AT (AUTO).

Normally you should use the AT (AUTO) setting because it automatically switches

between summer time and standard time. You should change the setting to STD

(standard time) or DST (summer time) in the following cases.

When using a time of a location that is not included in the watch’s list of 29 cities

−

When the preset AUTO standard time/summer time timing is incorrect for some −

reason

Daylight Saving Time (DST)

Daylight Saving Time (summer time) advances the time setting by one hour from

Standard Time. Remember that not all countries or even local areas use Daylight

Saving Time.

Note that you cannot switch between

x STD (standard time) and DST (daylight

saving time) while UTC* is selected as your Home City.

Coordinated Universal Time, the world-wide scientiﬁ c standard of timekeeping. The *

reference point for UTC is Greenwich, England.

E-35

If you do not perform any operation with the crown for about two minutes after x

pulling it out, crown operations will become disabled and the hand will not move

if you rotate the crown. If this happens, push the crown back in and then pull it

out again.

For details about city codes, see the “City Code Table” at the back of this

manual.

Rotate the crown to move the 2.

Second Hand to the city

code you want to select as your Home City.

Each time you select a city code, the

Hour Hand,

Minute Hand and

Day Indicator move to the

current time and day for that city code.

Push the crown back in to return to the Timekeeping 3.

Mode.



E-34

Conﬁ guring Home City Settings

The Home City is location where you will normally use the watch. You can choose

from a selection of city codes that represent 29 cities around the globe.

To conﬁ gure Home City settings

Note

This watch does not have a city code that corresponds

to Newfoundland.

Pull out the crown.1.

This will cause the

Second Hand to move to the

city code of the currently selected Home City.

This indicates the city code setting mode.



TYO (TOKYO)

E-33

Timekeeping

To enter the Timekeeping Mode, hold down C at least two seconds.

Hands and Indicators

Hour Hand

Second Hand

Minute Hand

Upper Dial Hand: Indicates the current hour in the

Home City time in 24-hour format.

Lower Dial Hand: Points to the day of the week.

Day Indicator



@>B

E-32

To select a mode

Each press of C will cycle between modes. The currently selected mode is indicated

by the

Lower Dial Hand.

Timekeeping Mode World Time Mode

Alarm Mode Countdown Timer Mode

Stopwatch Mode

E-31

Selecting a Mode

With this watch, everything starts from the Timekeeping Mode.

To determine the watch’s current mode

Check what the

Lower Dial Hand is indicating as shown

under “To select a mode” (page E-32).

To return to the Timekeeping Mode from any other

mode

Hold down C for at least two seconds.



E-30

Mode Reference Guide

Your watch has ﬁ ve “modes”. The mode you should select depends on what you want

to do.

To do this: Enter this mode: See:

Conﬁ gure Home City and DST (daylight saving time) settings x

Perform a time calibration signal receive operation x

Change the Auto Receive on/off setting x

Conﬁ gure time and day settings manually x

Measure temperature x

Timekeeping Mode E-33

View the current time in one of 29 cities around the globe

Conﬁ gure World Time City and summer time settings x

Swap the Home City and World Time City x

World Time Mode

E-53

E-54

E-57

Use the stopwatch to measure elapsed time Stopwatch Mode E-58

Use the countdown timer

Countdown Timer

Mode

E-61

Set an alarm time x

Turn the alarm ON or OFF x

Alarm Mode

E-64

E-67

Casio 5240 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio 5240

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info