Bedienungsanleitung Casio 5311 - GW-A1100 (Seite 4 von 11) (Englisch)

624480

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

Operation Guide 5311

E-39

To switch between standard time and summer time manually

1. Perform steps 1 and 2 under “To conﬁ gure Home City settings” (page E-36).

x Selecting a city code will cause the

Hour Hand,

Minute Hand, and

Upper Dial Hand to move automatically to the current time for the selected

city code.

x If you will use the watch in a city that is not included in the city code list, select a

city code that is in the same time zone as your city.

x Displaying the Home City Settings screen will cause the

Lower Dial Hand to

move to AT (auto switching), STD (standard time), or DST (daylight saving time).

AT (AUTO)

The watch automatically switches between standard time and daylight

saving time in accordance with its calendar.

STD The watch always shows standard time.

DST The watch always shows daylight saving time.

E-38

STD/DST Switching

You can select summer time or standard time independently for each city. The initial

default setting for all cities is AT (AUTO).

Normally you should use the AT (AUTO) setting because it automatically switches

between summer time and standard time. You should change the setting to STD

(standard time) or DST (summer time) in the following cases.

− When using a time of a location that is not included in the watch’s list of 29 cities

− When the preset AUTO standard time/summer time timing is incorrect for some

reason

Daylight Saving Time (DST)

Daylight Saving Time (summer time) advances the time setting by one hour from

Standard Time. Remember that not all countries or even local areas use Daylight

Saving Time.

x Note that you cannot switch between STD (standard time) and DST (daylight

saving time) while UTC* is selected as your Home City.

* Coordinated Universal Time, the world-wide scientiﬁ c standard of timekeeping. The

reference point for UTC is Greenwich, England.

E-37

x If you do not perform any operation with the crown for about two minutes after

pulling it out, crown operations will become disabled and the hand will not move

if you rotate the crown. If this happens, push the crown back in and then pull it

out again.

x For details about city codes, see the “City Code Table” at the back of this

manual.

2. Rotate the crown to move the

Second Hand to the city

code you want to select as your Home City.

x Each time you select a city code, the

Hour Hand,

Minute Hand and

Day Indicator move to the

current time and day for that city code.

3. Push the crown back in to return to the Timekeeping

Mode.



E-36

Conﬁ guring Home City Settings

The Home City is location where you will normally use the watch. You can choose

from a selection of city codes that represent 29 cities around the globe.

To conﬁ gure Home City settings

Note

x This watch does not have a city code that corresponds

to Newfoundland.

1. Pull out the crown.

x This will cause the

Second Hand to move to the

city code of the currently selected Home City.

x This indicates the city code setting mode.



TYO (TOKYO)

E-35

Timekeeping

To enter the Timekeeping Mode, hold down C at least two seconds.

Hand Functions

Hour Hand

Second Hand

Minute Hand

Upper Dial Hand: Indicates the current hour in the

Home City time in 24-hour format.

Lower Dial Hand: Points to the day of the week.

Day Indicator



@>B

E-34

To select a mode

Each press of C will cycle between modes. The currently selected mode is indicated

by the

Lower Dial Hand.

Timekeeping Mode World Time Mode

Stopwatch Mode

Countdown Timer Mode

Alarm Mode

E-33

To do this: Enter this mode: See:

x Set an alarm time

x Turn the alarm ON or OFF

Alarm Mode

E-75

E-78

Selecting a Mode

With this watch, everything starts from the Timekeeping Mode.

To determine the watch’s current mode

Check what the b

Lower Dial Hand is indicating as shown

under “To select a mode” (page E-34).

To return to the Timekeeping Mode from any other

mode

Hold down C for at least two seconds.



E-32

Mode Reference Guide

Your watch has ﬁ ve “modes”. The mode you should select depends on what you want

to do.

To do this: Enter this mode: See:

x Conﬁ gure Home City and DST (daylight saving time) settings

x Perform a time calibration signal receive operation or view

the last receive result

x Change the Auto Receive on/off setting

x Conﬁ gure time and day settings manually

x Determine magnetic north

Timekeeping Mode

E-35

E-48

x View the current time in one of 29 cities around the globe

x Conﬁ gure World Time City and summer time settings

x Swap the Home City and World Time City

World Time Mode

E-63

E-64

E-67

Use the stopwatch to measure elapsed time Stopwatch Mode E-69

Use the countdown timer

Countdown Timer

Mode

E-72

E-31

Radio-controlled Atomic Timekeeping Precautions

x Strong electrostatic charge can result in the wrong time setting.

x Even if a receive operation is successful, certain conditions can cause the time

setting to be off by up to one second.

x The watch is designed to update its day setting automatically for the period from

January 1, 2000 to December 31, 2099. Updating of the day setting by signal

reception will no longer be performed starting from January 1, 2100.

x If you are in an area where signal reception is not possible, the watch keeps time

with the precision noted in “Speciﬁ cations” (page E-95).

x The receive operation is disabled under any of the following conditions.

− While power is at Level 2 or lower (page E-16)

− While the watch is in the power recovery mode (page E-17)

− While the watch is in the function sleep state (power saving, page E-19)

− While the watch is not in the Timekeeping Mode

− While a direction reading or Countdown Timer operation is in progress (even if the

watch is in the Timekeeping Mode)

x A receive operation is cancelled if an alarm sounds while it is being performed.

E-30

Note

x The

Second Hand will indicate N (NO) if you have adjusted the time or day

setting manually since the latest receive operation.

To turn auto receive on and off

1. In the Timekeeping Mode, press B. The

Second

Hand will move to Y (YES) or N (NO) to indicate the last

calibration signal receive result.

2. Pull out the crown.

The

Second Hand will perform one full revolution and

then stop at the current on/off setting.

3. Rotate the crown to move the

Second Hand to the

setting you want.

x To turn on auto receive, select Y (YES).

x To turn off auto receive, select N (NO).

4. Push the crown back in to return to the Timekeeping

Mode.



Y (YES)

N (NO)

Casio 5311 - GW-A1100 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio 5311 - GW-A1100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info