Operation Guide 5369 (MTG)
E-39
The countdown timer can be confi
about 10 seconds when the timer reaches zero.
Hand Functions
z
x
c
v
b
n
(1 revolution = 60 minutes).
m
(1 revolution = 120 minutes).
, TR .
x
To enter the Countdown Timer Mode
Refer to the Mode Reference Guide (page E-21).
x
Lower Dial Hand to move to TR .
E-38
To start an Auto Start operation
1. B .
x
Small Minute Hand ,
Small Hour Hand , and
Small Hour Hand (24-hour) to
move to the current Auto Start time.
x B to toggle between the normal stopwatch screen and the Auto Start time screen.
2. A .
x
x
“To measure elapsed time” (page E-36) and “To measure split times” (page E-36).
Note
x A .
x
x
time operation. However, you can recall the last Auto Start time you set by pressing B .
E-37
Auto Start
Auto Start starts a countdown from a specifi
elapsed time measurement when the countdown reaches zero.
To set the Auto Start Time
x
1.
x
operations will become disabled and the watch hands will no longer move when you rotate the
crown. If this happens, push the crown back in and then pull it out again.
2.
b
n
m
x
step.
x
change.
3. C .
4.
x
step.
5.
E-36
A
A B
Start Stop Reset
x A to restart the stopwatch without resetting it will resume the elapsed time operation from
where it was last stopped.
A
B
Display of normal
measurement returns after
5 seconds.
A B
Start Split Stop Reset
x B again while a split time is indicated will cause the hands to jump to a new (current) split
time.
x A while a split time is indicated will stop the elapsed time operation, causing the hands to
jump to the stop time.
Note
x
measurement will stop automatically when the maximum time is reached.
x
x B will not perform a reset operation while the hands are moving to elapsed timekeeping after
you enter the Stopwatch Mode.
x
Lower Dial Hand indicates the 1/20 (0.05)-second count for the fi
elapsed time operation. The
Second Hand will jump to the current value whenever A (Stop) is
pressed.
E-35
The stopwatch measures elapsed time and split times.
Hand Functions
z
x
c
v
b
n
(1 revolution = 60 minutes).
m
(1 revolution = 120 minutes).
,
operation.
To enter the Stopwatch Mode
Refer to the Mode Reference Guide (page E-21).
x
Lower Dial Hand to move to 0 .
E-34
Swapping your Home City and World Time City
You can use the procedure below to swap your Home City and World Time City. This capability can come
in handy when you frequently travel between two locations in different time zones.
The following example shows what happens when the Home City and World
Time City are swapped while the Home City originally is TOKYO (TYO ) and
the World Time City is NEW YORK (NYC ).
Home City World Time City
Before swapping
TOKYO (TYO)
10:08 p.m.
(Standard time)
NEW YORK (NYC)
9:08 a.m.
(Daylight saving time)
After swapping
NEW YORK (NYC)
9:08 a.m.
(Daylight saving time)
TOKYO (TYO)
10:08 p.m.
(Standard time)
To swap your Home City and World Time City
Hold down A for about three seconds.
x NEW YORK in this example) your new Home City. At the same
time, it will change your previous Home City to your new World Time City.
x x
Second Hand will point to the new Home City (NEW YORK in this example) for about one
second.
Note
x
enables calibration signal reception for that city.
E-33
2.
Second Hand to the city code you want to select as the World Time
City.
x
Small Minute Hand ,
Small Hour Hand , and
Small Hour
Hand (24-hour) move to the current time. For details about city codes, see the “City Code Table” at
the back of this manual.
x
Second Hand to 12 o’clock while selecting a city code, it will
automatically perform one full revolution and stop at 12 o’clock from the opposite direction.
x
that there is something wrong with your Home City settings. Use the procedure under “To confi
Home City settings” (page E-24) to correct the Home City settings.
3. A for about one second to cycle through the summer time settings as shown below.
x AT (AUTO ) enables automatic switching between standard time and summer time. For
details about the AT (AUTO ), STD and DST settings, see “STD/DST Switching” (page E-26).
AA
AT (AUTO) STD DST
A
4.
E-32
You can specify one other city from the watch’s 29 time zones as your World Time City. After you do, the
watch will indicate the current time in that city. The currently selected city is called the “World Time City”.
Hands and Indicators
The hands below indicate the current time in the World Time City.
b
n
m
To enter the Dual Time Mode
Refer to the Mode Reference Guide (page E-21).
x
Lower Dial Hand to
move to the current day of the week (SU /MO /TU /WE /TH /FR /SA ).
To view the time in another time zone
1.
x
Second Hand points to the currently selected World Time city code.
x
Lower Dial Hand will indicate AT (AUTO ), STD (standard time) or DST (daylight saving time),
which indicates the current daylight saving time setting.
x
automatically cause crown operations to become disabled. If this happens, press the crown back in,
pull it out, and then start the operation over again.
