Bedienungsanleitung Casio 5394 - OCW-P1000 (Seite 7 von 9) (Englisch)

624833

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

Operation Guide 5394 (OC)

E-55

Adjusting Home Positions

Strong magnetism or impact can cause the hands and/or day indicator setting to be off, even if the watch

is able to perform the time calibration signal receive operation.

Auto Home Position Adjustment

Auto correction of hand home positions corrects the hand position automatically.

x Auto correction is performed in the Timekeeping Mode only.

x Auto correction corrects the positions of all hands. For the day Indicator, you must perform the manual

adjustment procedure under “To adjust home positions” (page E-56).

x If the

Upper Dial Hand is 12 hours off of the current correct time, correct the setting using the

procedure under “To adjust home positions” (page E-56).

Manual Home Position Adjustment

Perform the procedure in this section if auto home position adjustment is not possible for some reason.

x Hand home position adjustment is not required if the time and day settings are correct.

Note

x Any time after you enter the home position adjustment mode in step 2 of the following procedure, you

can return to the Timekeeping Mode by pushing the crown back in. In this case, any adjustments you

made before the watch returned to the Timekeeping Mode will be applied.

x If you do not perform any operation with the crown for about two minutes after pulling it out, crown

operations will become disabled. If this happens, push the crown back in and then pull it out again.

E-54

6. After the settings are the way you want, push the crown back in to exit the alarm setting mode.

x The alarm always works based on the time kept in the Timekeeping Mode.

x The watch will return to the Timekeeping Mode automatically if you do not perform any operation in

the Alarm Mode for about two or three minutes.

x If you do not perform any operation with the crown for about two minutes after pulling it out, crown

operations will become disabled. If this happens, push the crown back in and then pull it out again.

To turn the alarm on or off

In the Alarm Mode, press A to toggle the alarm between on and off. The

Second Hand will indicate the

current ON/OFF setting.

Note

x The alarm will not sound if battery power is low.

x The alarm will not sound if the watch is in the Power Saving sleep state.

To stop the alarm

Press any button.

E-53

To change the alarm time setting

1. In the Timekeeping Mode, press B four times to enter the Alarm Mode.

x The

Lower Dial hand will move to AL.

2. Pull out the crown to enter the alarm setting mode.

x You can toggle between the hour and minute setting mode, and the hour only setting mode by

pressing B.

Hour/Minute Hour

3. Rotate the crown to set the alarm time.

x The

Hour Hand will also move.

x See “Using the Crown” (page E-4) for information about high-speed hand movement.

4. Press B to switch to the hour setting mode.

x The

Hour Hand will move slightly left and right to indicate the

Hour Hand setting mode.

5. Rotate the crown to adjust the hour setting only.

x Check the 24-hour time indicated by the

Upper Dial Hand to see if the current setting is a.m. or

p.m.

x See “Using the Crown” (page E-4) for information about high-speed hand movement.

E-52

Using the Alarm

When the alarm is turned on, an alarm will sound for about 10 seconds each day when the time in the

Timekeeping Mode reaches the preset alarm time. This is true even if the watch is not in the Timekeeping

Mode.

Hands and Indicators

Hour Hand: Indicates the currently set alarm time hour.

Second Hand: Indicates the current alarm ON/OFF setting.

Minute Hand: Indicates the currently set alarm time minute.

Upper Dial Hand: Indicates the hour setting of the current alarm time in

24-hour format.

Lower Dial Hand: Points to AL.



 



E-51

3. Rotate the crown to set the countdown start time.

x The maximum countdown start time setting is 60 minutes. To set a countdown start time of 60 minutes,

move the

Minute Hand to 12 o’clock.

x See “Using the Crown” (page E-4) for information about high-speed hand movement.

4. Push the crown back in to exit the countdown start time setting mode.

x If you do not perform any operation with the crown for about two minutes after pulling it out, crown

operations will become disabled. If this happens, push the crown back in and then pull it out again.

To perform a countdown timer operation

A C

Start Stop Zero Reset

x A time-up alert sounds for 10 seconds when the countdown reaches 0, and then the timer displays the

start time.

x The alarm will not sound if battery power is low.

x Pulling out the crown while a countdown is in progress will stop the countdown and enter the

countdown start time setting mode.

Important!

x Time calibration signal reception is disabled while the watch is in the Countdown Timer Mode.

To stop the alarm

Press any button.

E-50

Using the Countdown Timer

The countdown timer start time can be set in one-minute increments up to 60 minutes. An alarm sounds

for about 10 seconds when the timer reaches zero.

Hands and Indicators

Second Hand: Indicates countdown or elapsed seconds.

Minute Hand: Indicates countdown or elapsed minutes.

Lower Dial Hand: Points to TR.

x All hands move counterclockwise during a countdown.

To specify the countdown start time

1. In the Timekeeping Mode, press B three times to enter the Countdown

Timer Mode.

x The

Lower Dial Hand will move to TR.

2. In the Countdown Timer Mode, pull out the crown.

x This enters the countdown start time setting mode.













E-49

To enter and exit the Stopwatch Mode

In the Timekeeping Mode, press B twice to enter the Stopwatch Mode.

x The

Lower Dial Hand will move to ST.

To perform an elapsed time operation

A A A C

Start Stop (Restart) (Stop) Zero Reset

To perform ﬂ yback timing

Pressing C while an elapsed time operation is in progress performs zero reset and immediately resumes

timing from there. You can do this as many times as you want.

A C C

.....

A C

Start 1 Start 2 Start 3 Stop Zero Reset

x An ongoing elapsed time measurement operation continues even if you pull out the crown or changing

to a different mode.

x The

Second Hand, which indicates the 1/20 (0.05)-second count during stopwatch operation, moves

only 30 seconds after an elapsed time measurement operation is started or restarted. After that, the

Second Hand stops.

E-48

Using the Stopwatch

You can use the stopwatch to measure elapsed times. A ﬂ yback feature (page E-49) lets you reset the

stopwatch to zero without stopping time measurement.

Hands and Indicators

Hour Hand: Indicates the stopwatch minute count

(1 revolution = 60 minutes).

Second Hand: Indicates the 1/20 (0.05)-second count during stopwatch

operation.

Minute Hand: Indicates the stopwatch seconds count.

Upper Dial Hand: Indicates the stopwatch minute count

(1 revolution = 120 minutes).

Lower Dial Hand: Points to ST.



 

 

Casio 5394 - OCW-P1000 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info