Bedienungsanleitung Casio CT-X5000 (Seite 110 von 157) (Englisch, Spanisch)

723237

110

Zoom out

Zoom in

Vorherige Seite

1/157

Nächste Seite

EN-109

Using the MIDI Recorder to Record

When you are editing the system track, you

can specify the event input target part.

• See “Selecting a System Track Part” (page EN-110).

• This step is not necessary when you are editing a solo

track. Proceed to step 6.

If necessary, specify the velocity (keyboard

touch) and gate time rate (actual length) of the

note event you are about to input.

• The velocity and gate time rate settings you specify

here are applied to all of the note events you input until

you change them.

• Velocity can be specified as a value (1 to 127) or by

actually pressing a key (which sets a velocity in

accordance with your key pressure). The initial default

is 100.

• The gate time rate specifies the note length as a

percentage (1 to 100%) of the note value you specify

in step 7. For example, when the gate time rate is 80%

(initial default), a quarter note (96 ticks) becomes 76

ticks (96×0.8=76.8, decimal part cut off).

* When “Key On” is selected, the velocity of the keyboard

press when inputting the note event is reflected in the

velocity value.

Specify the note value (event length) of the

event you are about to input in step 8.

*1 If you want to input a dotted note or triplet note, first press

a key from [1] to [6], and then press [7] or [8]. To input a

dotted quarter note, for example, press [3] and then [7].

• The note value specified in accordance with the key

input will appear on the right side of the display.

Specify the event to be input.

*2 Extends the length of the previously input note event. For

example, if you input a quarter note event and wish to

extend it by an eighth note, perform the following button

operation: bm number key [4] (eighth note) -

cs REGISTRATION [3] (Tie).

• Inputting an event advances the input point by the note

value amount you specified in step 7.

Repeat steps 5 through 8 as required.

• The operation in step 5 is not necessary as long as the

target part remains the same.

10.

To exit the Step Input Mode, press

cs REGISTRATION [1].

This causes the [STEP] indicator to disappear.

To specify this: Perform this operation:

Velocity (1) Press cs REGISTRATION [4].

(2) Use bn [–] and [+], or the bl dial to

specify a value or select “Key

On”.*

(3) Press the [4] (EXIT) bm number

key.

Gate Time Rate (1) Press cs REGISTRATION [5].

(2) Use bn [–] and [+] or the bl dial to

specify a percent value.

(3) Press the [4] (EXIT) bm number

key.

To input this note value: Press this bm number key:

Whole [1]

Half [2]

Quarter [3]

Eighth [4]

Sixteenth [5]

Thirty-second [6]

Dotted note*

[7]

Triplet*

[8]

To input this: Perform this operation:

Note event After specifying a note value in step 7,

press the keyboard key for the note

you want to input. Pressing multiple

keyboard keys at the same time inputs

a chord.

Rest After specifying a note value in step 7,

press cs REGISTRATION [2].

Tie*

After specifying a note value of a note

to tie with the previous note event in

step 7, press cs REGISTRATION

[3].

2 26

CTX5000_3000_EN.book 109 ページ２０１８年２月２６日　月曜日　午後３時５６分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Casio CT-X5000 Seite 110

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio CT-X5000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info