Bedienungsanleitung Casio CT-X5000 (Seite 111 von 157) (Englisch, Spanisch)

723237

111

Zoom out

Zoom in

Vorherige Seite

1/157

Nächste Seite

Using the MIDI Recorder to Record

EN-110

■ Selecting a System Track Part

When the system track is specified as the event edit target

track, you can use the buttons below to select the part to be

edited. You can find out the selection status of each part by

checking for the indicators shown in the “Display” column of

the table.

• The UPPER 1 and UPPER 2 parts can be selected at the

same time. The LOWER 1 and LOWER 2 parts can be

selected at the same time. Step inputting an event while

two parts are selected will simultaneously input the same

event into both parts.

• Auto harmonize part and the parts of phrase pads 1

through 4 can only be selected individually. Selecting these

parts will cause the indicators of the other parts to

disappear.

Perform the procedure under “To enter the

Song Editing Mode” (page EN-99).

Use the [1] (V) and [3] (W) bm number keys

to display “TrkEvent”, and then press [6]

(ENTER).

This displays “Trk Sy”

Use bn [–] and [+] or the bl dial to specify the

system track, and then press [6] (ENTER).

This displays the [EVENT] indicator.

If there is no [ACCOMP] indicator displayed,

press cm ACCOMP to display it.

Use the [2] (w) and [5] (q) bm number keys to

display the event within the measure from

which you want to start step input.

• The step input start point is the beginning of the

measure.

Press cs REGISTRATION [1].

This displays the [STEP] indicator and enters the Step

Input Mode.

If necessary, specify the chord event velocity

(keyboard touch).

• For information about how to specify the setting, see

step 6 under “To input note events using step input”

(page EN-108).

Specify the event length of the event you will

input in step 9.

• For information about how to specify the setting, see

step 7 under “To input note events using step input”

(page EN-108).

Specify the event to be input.

*1 For details about chord fingering modes, see “Changing

Accompaniment Keyboard Settings” (page EN-48).

*2 For information about how to specify this setting, see step

8 under “To input note events using step input” (page

EN-108).

10.

Repeat steps 7 through 9 as required.

To select this

part:

Press this button: Display

UPPER 1 cs REGISTRATION [7]

UPPER 2 dq UPPER LAYER

LOWER 1 dp SPLIT

LOWER 2

dq UPPER LAYER

(Long-press)

Auto

Harmonize

do AUTO HARMONIZE

Phrase Pad 1 cq PHRASE PAD [P1]

Phrase Pad 2 cq PHRASE PAD [P2]

Phrase Pad 3 cq PHRASE PAD [P3]

Phrase Pad 4 cq PHRASE PAD [P4]

To input chord events using step input

To input this: Perform this operation:

Chord Event After specifying an event length in step 8,

use the accompaniment keyboard to

specify a chord.*

Rest

(NonChord)

After specifying an event length in step 8,

press cs REGISTRATION [2].

Tie*

After specifying the event length of a

chord to tie with the previous chord event

in step 8, press cs REGISTRATION [3].

CTX5000_3000_EN.book 110 ページ２０１８年２月２６日　月曜日　午後３時５６分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Casio CT-X5000 Seite 111

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio CT-X5000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info