Bedienungsanleitung Casio KLC500 (Seite 9 von 52) (Englisch)

506040

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

E-8

Data Storage

• The label printer has a built-in memory backup battery that supplies the power

required to retain text and other data in memory.

A label on the back of the label printer shows when the memory backup bat-

tery needs to be replaced. If the memory backup battery goes dead, data

stored in memory will be corrupted or lost completely. Whenever it gets close

to the battery replacement date noted on the label, take the label printer to

your original retailer to have it replaced. Note that you will be charged for the

replacement.

• Be sure to keep separate written copies of all text data stored in label printer

memory.

Turning Power On and Off

Press ON to turn power on, and OFF to turn power off.

Important! If you are using the label printer for the first time, you should reset

it first.

Power On Recall Function

Whenever you turn power off, any input that is on the display is automatically

stored in memory. Then the next time you turn on power, the message “PRESS

[SET] TO RECALL” appears on the display. Pressing SET when this message is

on the display recalls the text that was on the screen when you last turned off

power.

• Pressing any key besides SET, FUNCTION, SHIFT or CODE clears the text

from memory.

Resetting the Memory

You should reset the memory of the label printer before using it for the first time,

after you have not used it for a long time, or if nothing happens when you turn

power on.

Important! Resetting label printer memory clears its memory of all input data.

To reset the memory

1. Make sure that label printer power is off.

2. While holding down the PRINT and ESC

keys, press ON to turn power on.

3. Press SET to initialize the label printer or ESC to abort the reset operation

without initializing anything.

• See “Initial Settings” on page E-39 for information on the initial default set-

tings of the label printer following the reset operation.

Auto Power Off Function

If you do not perform any key operation for about thirty minutes, the label printer

automatically turns power off. To restore power, press ON.

Tape Cartridges

Use the procedures described below to load a tape cartridge into the label

printer. The label printer automatically detects what size tape is loaded.

Important! Never try to push the tape back into the cassette. Once tape is out

of the cassette, there is no way to wind it back in. Trying to do so can cause

operational problems with the label printer.

To load a tape cartridge

1. Make sure the label printer is turned off.

2. Press the cover release and open the cover.

• If there is a cartridge already in the label printer,

remove it by grasping the cartridge on both sides

with your thumb and forefinger, and lift straight

up.

3. Remove the stopper from a new tape cartridge

and check to see that the tape is ready to use.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Casio KLC500 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio KLC500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info