Bedienungsanleitung Casio QW3475 - GBD-H1000 G-SQUAD (Seite 36 von 58) (Englisch)

740165

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

Altitude Measurement

The watch takes altitude readings and

displays results based on air pressure

measurements taken by a built-in pressure

sensor.

Important!

●

The altitude readings displayed by the

watch are relative values that are

calculated based on barometric

pressure measured by the watch’s

pressure sensor. This means that

barometric pressure changes due to

weather can cause altitude readings

taken at the same location to be

different. Also note that the value

displayed by the watch may be

different from the actual elevation and/

or sea level elevation indicated for the

area where you are located. When

using the watch’s altimeter while

mountain climbing, it is recommended

that you regularly calibrate its readings

in accordance with local altitude

(elevation) indications.

Calibrating Altitude Readings

●

The altitude correction value you

specify and/or barometric pressure

changes may cause a negative value

to be displayed.

●

Check the information at the link below

to find out about how to minimize

differences between readings

produced by the watch, and values

provided by local altitude (elevation)

indications.

Altitude Reading Precautions

Checking the Current

Altitude

1. Enter the Altimeter Mode.

Navigating Between Modes

Changing Displayed Information

Entering the Altitude Mode will start

altitude measurement and display the

altitude at your current location.

●

The watch takes altitude readings every

second for about the first three minutes.

After that, it takes readings according to

the watch’s auto measurement interval

setting.

●

Check the information at the link below

to find out how to configure the auto

measurement interval.

Setting Up the Auto Measurement

Interval

●

To retrigger measurement, press (C).

●

Press (E) to return to the Timekeeping

Mode.

Note

●

Measurement range: -10,000 m to

10,000 m (-32,800 to 32, 800 feet)

(Measurement unit: 1 meter (5 feet))

Note that calibrating altitude readings

will cause a change in the

measurement range.

●

[----] will appear for the measured value

if it is outside the allowable range.

Value Screen

②

①

Graph Screen

①②

③

A　Current location altitude

B　Differential between reference altitude

and current altitude

C　Altitude graph

240m

Current reading

Setting a Reference Altitude

and Taking Relative Altitude

Readings

You can use the procedure below to display

the differential between a reference altitude

and another altitude. This makes it easy to

measure the altitude differential between two

points while climbing or trekking.

1. Use the contour lines on your map to

determine the altitude differential between

your current location and your destination.

2. Take an altitude reading of your current

location.

Checking the Current Altitude

3. Hold down (A) for at least two seconds.

This displays the Altimeter Mode setting

screen.

Pointer

4. Use (A) and (D) to move the pointer to

[DIFF RESET].

5. Use (C) to set your current location’s

altitude as the reference altitude.

This makes the altitude differential ±0 m

(±0 feet).

Operation Guide 3475

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Casio QW3475 - GBD-H1000 G-SQUAD Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info