Bedienungsanleitung Casio WK-6600 (Seite 71 von 132) (Englisch)

522439

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

Using the Song Sequencer

E-69

Use the R-17 (u, i) buttons to select a track

(Track 01 through Track 16).

Configure panel settings as required for your

performance.

• Configure the following settings: tone selection, tempo,

mixer settings, etc. For details about settings that can

be configured, see “Recording Start” under “System

Track and Track 01 through 16 Common Recording

Content” (page E-66) and “Track 01 through 16

Recording Content” (page E-66). For information about

mixer settings, see “Mixer Settings in the Song

Sequencer Mode” (page E-71).

Perform the following steps to configure beat

and other settings.

Start playing something on the keyboard.

• This will start recording and cause the C-2 (RECORD)

button to change from flashing to lit. During recording,

the display will show the current measure (MEASURE)

and beat (BEAT).

• To input one or more rests before starting recording,

press the L-16 (START/STOP) button to start

recording, and then start keyboard play at the point you

want.

•PITCH BEND wheel (S-1) and pedal operations are

also recorded.

• When recording reaches a point where there is less

than 100 notes of remaining memory capacity, the

current measure (MEASURE) and beat (BEAT) values

will start flashing.

To stop recording, press the L-16 (START/

STOP) button.

• At this time you can press the L-16 (START/STOP)

button to replay what you have just recorded. For

details about playing back recorded content, see

“Playing a Recorded Song” (page E-72).

To exit the song sequencer, press the C-3

(SONG SEQUENCER) button or the R-15 (EXIT)

button.

(1) While holding down the R-13 (FUNCTION) button,

press the C-13 (MENU) button.

This will display a menu like the one shown below, with

the 0 next to “Beat” (beat).

(2) Use the dial or R-14 (–, +) buttons to configure the beat

setting.

You can specify a beat setting of 2/4 to 8/4, 2/8 to 16/8.

(3) Use the R-17 (y) button to move the 0 to

“Metronome” and then use the R-14 (–, +) buttons to

turn the metronome on or off.

Turning on the metronome causes it to count a count

during recording, but not during playback.

(4) Use the R-17 (y) button to move the 0 to “Precount”

and then use the R-14 (–, +) buttons to turn the

precount on or off.

Turing on the precount inserts a one-measure count

before the start of recording when you press the L-16

(START/STOP) button in step 7.

(5) Use the R-17 (y) button to move the 0 to “RecType”,

and then use the R-14 (–, +) buttons to select “REPL”

or “OVDB”.

When you want to perform this type

of recording:

Select this

RecType option:

Delete any data currently existing in

the track being recorded to and start a

new recording.

REPL (Replace)

Overdub any data currently existing in

the track being recorded to with the

new recording.

OVDB (Overdub)

(6) Press the R-15 (EXIT) button to exit the menu.

CTK6200_e.book 69 ページ２０１１年１２月２７日　火曜日　午後８時２０分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Casio WK-6600 Seite 71

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio WK-6600

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info