Bedienungsanleitung CAWI 7202 (Seite 2 von 7) (Französisch)

622510

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

Bedienungsanleitung Nr. 9999-041-0

Seite 2

B7202_E_1.pmd

12.06.2003

Remove the old batteries and replace them with two new 1.5

volt AA (alkaline) batteries. The direction in which the batteries

are to be installed is shown inside the battery compartment cover.

The programmed combination will be retained during battery

replacement.

7. Emergency opening

The electronic lock is also equipped with an emergency release

feature (double-bit safety lock). This special function makes it

possible to open the container even though the batteries were

not changed in due time or if the electronics failed or the

combination was lost. Furthermore, using the emergency key to

unlock and open the door prepares the system for programming

a new combination; see 8.2. The access to the emergency

release lock is inside the battery compartment; behind the

batteries; see Figure 1.

Store the emergency release key carefully in a secure

place. Do not leave it in the safe!

Functioning:

Insert the supplied double-bit key in the emergency release

lock. (The mark on the head of the key must point away from

the hinge.)

Now turn the key clockwise, all the way to the stop; use the

keypad lever to release the electronic lock and open the door.

Close the door to the safe. Move the keypad lever downward

(red screw cover cap must be concealed by the keypad

lever). Turn the key counterclockwise and withdraw it from

the emergency release lock. Slide the battery compartment

cover back on to the keypad housing and affix it with the

Phillips screw.

8. Programming the electronic lock

Before you use your safe for the first time it is necessary, for

security reasons, to enter your own personal combination; the

factory combination must not be retained. Programming is

possible only with the door open and with the electronic lock

released. Select your new six-digit combination before starting

the easy programming sequence. Do not use any personal data

for this combination, such as birthdays or other information which

could be derived from knowledge about your person. Store your

combination in a safe place so that only you have access to it.

1.2 General

Even though operation is very simple, you should nonetheless

read these instructions carefully and completely before starting,

in order to prevent operating errors. These operating instructions

apply to an electronic lock which is installed in a high-security

container such as a safe. A tone will sound briefly to verify the

entry each time a button is pressed. No more than 30 seconds

may elapse between entries as otherwise all the information

entered up to that point will be discarded.

2. Opening the electronic lock

Enter either the factory combination, pressing the 0 _ 1 2 3 4 5 6

buttons, or your own new master combination.

You may press the „C“ key to correct the entry. In this

case you will have to repeat the entire entry sequence.

Correct entry is confirmed with a tone. The green LED

will now blink and the electronic lock is cleared for opening for a

period of 12 seconds. The door to the safe can now be unlocked

using the keypad lever and the fingertip grip. The green LED will

blink at a 3-second interval for as long as the electronic lock is

open.

The keypad lever may not be under pressure before the

acoustic and optical clearance signals are emitted. If the

keypad lever is not used within 12 seconds to open the door,

then the electronic lock will automatically be re-locked.

3. Closing the electronic lock

Close the door and turn the keypad lever back to the stop. The

keypad lever will have to cover the red marking completely. The

electronic lock is automatically locked in this position. Two signal

tones of the same frequency will sound to indicate that the

electronic lock has been locked; the green LED will light once.

In the interest of security, attempt to turn the handle to

ensure that the container is properly closed.

4. Time-out following erroneous entries

Twelve signal tones will sound and the red LED will light if an

invalid combination is entered. You now have three more tries to

enter a valid combination. After the fourth consecutive invalid

entry, however, the time-out period commences; the keypad will

accept no entries during this 10-second period. This time-out

period will be extended by 10 additional seconds following each

subsequent invalid entry up to a maximum time-out period of 15

minutes. The time-out period cannot be interrupted with the „C“

button.

5. Correction with the „C“ button

If you press the „C“ button during the course of an entry

sequence, then all digits previously entered will be canceled.

Any programming mode which might have been commenced will

also be terminated. You must initiate programming once again,

from the beginning, by pressing the „*“ button.

Exception: Neither the time-out period following erroneous

entries nor the low battery warning period can be interrupted

with the „C“ button.

6. Battery monitoring, replacing the battery

If the battery charge is insufficient, then a high-low warning

tone will sound 10 times after the combination is entered and the

red and green LEDs will blink alternately. This is to remind you to

install two new 1.5 volt (AA alkaline) batteries within the next

few days.

Replacing the batteries: The battery compartment cover is

located to the right of the keypad housing. Slide the battery

compartment cover off the keypad housing, in the direction

indicated by the arrow. See Figure 1.

Programming modes

P - No. 0: Programming and changing the

master combination

Programming a new master combination

using the emergency opening lock

P - No. 1: Programming, changing or deleting any of the

5 user combinations

P - No. 2: Programming or deleting a

combination interlock (duality principle)

P - No. 3: Programming and deleting a

timed delay period

P - No. 6: Programming the time lock

CAWI 7202 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von CAWI 7202

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info