Bedienungsanleitung Celestron CGE Pro 1100 (Seite 51 von 72) (Englisch)

667041

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

The three collimation screws are located

on the front of the secondary mirror

housing.

While your telescope requires little maintenance, there are a few things to remember that will ensure your telescope

performs at its best.

Care and Cleaning of the Optics

Occasionally, dust and/or moisture may build up on the corrector plate of your telescope. Special care should be

taken when cleaning any instrument so as not to damage the optics.

If dust has built up on the corrector plate, remove it with a brush (made of camel’s hair) or a can of pressurized air.

Spray at an angle to the lens for approximately two to four seconds. Then, use an optical cleaning solution and

white tissue paper to remove any remaining debris. Apply the solution to the tissue and then apply the tissue paper

to the lens. Low pressure strokes should go from the center of the corrector to the outer portion.

Do NOT rub in

circles!

You can use a commercially made lens cleaner or mix your own. A good cleaning solution is isopropyl alcohol

mixed with distilled water. The solution should be 60% isopropyl alcohol and 40% distilled water. Or, liquid dish

soap diluted with water (a couple of drops per one quart of water) can be used.

Occasionally, you may experience dew build-up on the corrector plate of your telescope during an observing

session. If you want to continue observing, the dew must be removed, either with a hair dryer (on low setting) or by

pointing the telescope at the ground until the dew has evaporated.

If moisture condenses on the inside of the corrector, remove the accessories from the rear cell of the telescope.

Place the telescope in a dust-free environment and point it down. This will remove the moisture from the telescope

tube.

To minimize the need to clean your telescope, replace all lens covers once you have finished using it. Since the rear

cell is NOT sealed, the cover should be placed over the opening when not in use. This will prevent contaminants

from entering the optical tube.

Internal adjustments and cleaning should be done only by the Celestron repair department. If your telescope is in

need of internal cleaning, please call the factory for a return authorization number and price quote.

Collimation

The optical performance of your telescope is directly related to its collimation,

that is the alignment of its optical system. Your telescope was collimated at the

factory after it was completely assembled. However, if the telescope is dropped

or jarred severely during transport, it may have to be collimated. The only

optical element that may need to be adjusted, or is possible, is the tilt of the

secondary mirror.

To check the collimation of your telescope you will need a light source. A bright

star near the zenith is ideal since there is a minimal amount of atmospheric

distortion. Make sure that tracking is on so that you won’t have to manually track

the star. Or, if you do not want to power up your telescope, you can use Polaris.

Its position relative to the celestial pole means that it moves very little thus

eliminating the need to manually track it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Celestron CGE Pro 1100 Seite 51

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info