Bedienungsanleitung Celestron CGE Pro 1100 (Seite 52 von 72) (Englisch)

667041

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Figure 8-3

A collimated telescope

should appear

symmetrical with the

central obstruction

centered in the star's

diffraction pattern.

Before you begin the collimation process, be sure that your telescope is in thermal equilibrium with the

surroundings. Allow 45 minutes for the telescope to reach equilibrium if you move it between large temperature

extremes.

To verify collimation, view a star near the zenith. Use a medium to high power ocular — 12mm to 6mm focal

length. It is important to center a star in the center of the field to judge collimation. Slowly cross in and out of

focus and judge the symmetry of the star. If you see a systematic skewing of the star to one side, then re-collimation

is needed.

To accomplish this, you need to tighten the secondary collimation screw(s) that move the star across the field toward

the direction of the skewed light. These screws are located in the secondary mirror holder (see figure 8-1). Make

only small 1/6 to 1/8 adjustments to the collimation screws and re-center the star by moving the scope before

making any improvements or before making further adjustments.

To make collimation a simple procedure, follow these easy steps:

1. While looking through a medium to high power eyepiece, de-focus a bright star until a ring pattern with a

dark shadow appears (see figure 8-2). Center the de-focused star and notice in which direction the central

shadow is skewed.

2. Place your finger along the edge of the front cell of the telescope (be careful not to touch the corrector

plate), pointing towards the collimation screws. The shadow of your finger should be visible when looking

into the eyepiece. Rotate your finger around the tube edge until its shadow is seen closest to the narrowest

portion of the rings (i.e. the same direction in which the central shadow is skewed).

3. Locate the collimation screw closest to where your finger is positioned. This will be the collimation screw

you will need to adjust first. (If your finger is positioned exactly between two of the collimation screws,

then you will need to adjust the screw opposite where your finger is located).

4. Use the hand control buttons to move the de-focused star image to the edge of the

field of view, in the same direction that the central obstruction of the star image is

skewed.

5. While looking through the eyepiece, use an Allen wrench to turn the collimation

screw you located in step 2 and 3. Usually a tenth of a turn is enough to notice a

change in collimation. If the star image moves out of the field of view in the

direction that the central shadow is skewed, than you are turning the collimation

screw the wrong way. Turn the screw in the opposite direction, so that the star

image is moving towards the center of the field of view.

6. If while turning you notice that the screws get very loose, then simply tighten the

other two screws by the same amount. Conversely, if the collimation screw gets

too tight, then loosen the other two screws by the same amount.

Figure 8-2 -- Even though the star pattern appears the same on both sides of focus, they are asymmetric. The

dark obstruction is skewed off to the left side of the diffraction pattern indicating poor collimation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Celestron CGE Pro 1100 Seite 52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info