Bedienungsanleitung Celestron CPC Deluxe 800 HD - 11007 (Seite 6 von 50) (Englisch)

667030

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

>> www.celestron.com



The CPC DeluxeHD telescope comes completely pre-assembled and can be operational in a matter of minutes. The CPC and its accessories are

conveniently packaged in one reusable shipping carton while the tripod comes in its own box. Included with your telescope are the following:

#11007 #11008 #11009

CPC Deluxe 800 HD CPC Deluxe 925 HD CPC Deluxe 1100 HD

Diameter 203 mm (8”) Edge HD Optics 235 mm (9.25”) Edge HD Optics 280 mm (11”) Edge HD Optics

Focal Length 2032 mm f/10 2350 mm f/10 2800 mm f/10

Eyepiece 40 mm - 1.25” (51x) 23 mm - 2” (102x) 23 mm - 2” (122x)

Finderscope 9x50 9x50 9x50

Diagonal 90° - 1.25” 90° - 2” with 1.25” adapter 90° - 2” with 1.25” adapter

Mount CPC Altazimuth CPC Altazimuth CPC Altazimuth

Tripod 2” Stainless Steel 2” Stainless Steel 2” Stainless Steel

NexRemote Telescope Control NexRemote Telescope Control NexRemote Telescope Control

Software Software with RS-232 cable Software with RS-232 cable Software with RS-232 cable

Power Car Battery Adapter Car Battery Adapter Car Battery Adapter

Setting up the Tripod

For maximum rigidity, the Celestron heavy duty tripod has a leg support

bracket/accessory tray. This bracket ts snugly against the tripod legs,

increasing stability while reducing vibration and exure. However, the

tripod must be shipped with the leg support bracket detached so the

tripod legs can collapse. To set up the tripod:

1. Hold the tripod with the head up and the legs pointed toward

the ground.

2. Pull the legs away from the central column until they will not separate

any further. The top of each tripod leg presses against the tripod head

to indicate maximum separation.

3. Remove the tension knob, located on the central column. See gure 3-1.

4. Place the leg support bracket over the central rod so that the cups on

the end of each bracket are directly underneath each leg.

5. Rotate the tension knob until the bracket is secure against the tripod

legs. 

The tripod will now stand by itself. Once the telescope is attached to the

tripod, readjust the tension knob to ensure that the leg support bracket

is snug. Once again, do not over tighten!

Start by removing the telescope and tripod from their shipping cartons

and set the telescope’s round base on a sturdy at surface. Always

carry the telescope by holding it from the lower portion of the fork arm

on the hand control side and from the handle on the opposite side.

Remove all of the accessories from their individual boxes. Remember

to save all of the containers so that they can be used to transport the

telescope. Before attaching the visual accessories, the telescope should

be mounted on the tripod and the tube should be positioned horizontal

to the ground.

>>

























Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Celestron CPC Deluxe 800 HD - 11007 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info