Bedienungsanleitung Celestron CPC Deluxe 800 HD - 11007 (Seite 7 von 50) (Englisch)

667030

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

>> www.celestron.com

Adjusting the Tripod Height

The tripod that comes with your CPC telescope is adjustable. To adjust

the height at which the tripod stands:

1. Loosen the extension clamp on one of the tripod legs (see gure 3-1).

2. Extend the leg to the desired height.

3. Tighten the extension clamp to hold the leg in place.

4. Repeat this process for each of the remaining legs making sure that

the tripod is level when complete.

You can do this while the tripod legs are still folded together.

Remember that the higher the tripod legs are extended, the less stable

it is. For casual observing, this may not pose a problem. However, if

you plan on doing photography, the tripod should be set low to ensure

stability. A recommended height is to set the tripod in such a manner

that you can look directly into the eyepiece on the telescope with a

diagonal while seated.

Attaching the CPC to the Tripod













After the tripod is set up, you are now ready to attach the telescope.

The bottom of the CPC base has three threaded holes that mount to the

tripod head and one hole in the center that goes over the positioning pin

on the tripod head.

1. Place the center hole in the bottom of the telescope base over the

positioning pin in the center of the tripod head.

2. Rotate the telescope base on the tripod head until the three feet on

the bottom of the base fall into the feet recesses on the top of the

tripod head.

3. Thread the three attached mounting bolts from underneath the

tripod head into the bottom of the telescope base. Tighten all

three bolts.

You are now ready to attach the visual accessories onto the telescope

optical tube.

Adjusting the Clutches

The CPC has a dual axis clutch system. This allows you to move the

telescope manually even when the telescope is not powered on.

However, both clutches need to be tightened down for the telescope to

be aligned for “GoTo” use. Any manual movement of the telescope will

invalidate your telescope’s alignment.

Before attaching your visual accessories, rst loosen the altitude locking

knob while holding the telescope tube by the rear cell handle. Rotate the

tube upwards until it is level with the ground and tighten the

locking knob.

Note: When transporting your telescope, make sure that both

clutches are somewhat loose; this will diminish the load placed on

the worm gear assemblies and protect them from damage.





















>>

The star diagonal is a prism or mirror that diverts the light at a right angle

to the light path of the telescope. This allows you to observe in positions

that are physically more comfortable than if you looked straight through.

To attach the 1.25” star diagonal onto the 8” optical tube:













1. Turn the set screw on the visual back until its tip no longer extends

into (i.e., obstructs) the inner diameter of the visual back.

2. Slide the chrome portion of the star diagonal into the visual back.

3. Tighten the set screw on the visual back to hold the star diagonal

in place.

If you wish to change the orientation of the star diagonal, loosen the set

screw on the visual back until the star diagonal rotates freely. Rotate the

diagonal to the desired position and tighten the set screw.

To attach the 2” star diagonal onto the 9.25/11” optical tubes:

1. Remove the visual back from the rear of the tube.

2. Attach the threaded ring of the 2” diagonal to the rear cell of

the telescope.

3. Loosen the thumb screws on the side of the diagonal and remove the

1.25” adapter from the barrel of the diagonal.

If you wish to change the orientation of the 2” star diagonal, loosen

the retaining ring that attaches the diagonal to the rear cell. Rotate the

diagonal to the desired position and tighten the retaining ring.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Celestron CPC Deluxe 800 HD - 11007 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info