Bedienungsanleitung Chamberlain WD962KEV (Seite 38 von 48) (Englisch)

555431

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Operation

Motion Detecting Control Panel (continued)

LOCK

The LOCK feature isdesigned to prevent activation ofthe garage door opener from remote controls

while still allowing activation from the door control and keyless entry.Thisfeature isuseful for added

peace of mind when the home isempty (i.e.vacation).

Activate: Pressand hold the LOCK button for 2 seconds.The command LED will flash aslong

as the lockfeature is activated and your handheld remote control will not operate your door at

thistime.

Deactivate: Press and hold the LOCK button again for 2 seconds.The command LED will stop

flashing and normal operation will resume.

TIMER-TO-CLOSE

DO NOT enable TTC if operating a one-piece door. The TTC can be turned on or offand the time

interval can be adjusted to 1, 5,and 10 minute intervals. Once the TTC hasbeen set and the door is

open, the selected close interval will blink and begin to count down to close the door.

Activate: Pressand hold the ON button until one of the TTC LEDs light up.Then pressthe ON

button again to cycle through the time interval options (the corresponding TTC LED will light for

each time interval). The garage door opener light bulbs will blink asconfirmation.

Deactivate: Press and hold the OFF button until all TTC LEDs turn off and a beep is heard from

the motor unit.

Temporarily hold door open (suspend TTC): Press and release the HOLD OPEN button. Press

the HOLD OPEN button again to resume normal TTC operation.

PROGRAM

Any compatible remote controls, wireless keyless entry, or MyQ

accessories can be programmed to the

garage door opener by pressing the Learn button.

ON (TTC)

OFF (TTC)

Command LED

Motion Sensor

Switch

LIGHT

Button

HOLD OPEN

Button(TTC)

Motion

Sensor

Push Bar

1, 5, and

10 Minute

TTC LED

LEARN Button

LOCK Button

Using the Smart Control Panel

SYNCHRONIZE THE DOOR CONTROL

To synchronize the door control to the garage door opener, pressthe push bar until the garage door

opener activates (itmaytake up to 3 presses). Test the door control bypressing the push bar,each press

of the push bar will activate the garage door opener.

Push Bar

LIGHT Button

Motion Sensor

Navigation Buttons

Screen

SMART CONTROL PANEL FEATURES

PUSH BAR

Press the push bar to open or close the door.

LIGHTS

Light Button

Press the LIGHT button to turn the garage door opener lights on or off. When the lights are turned on

they will stay on until the LIGHT button ispressed again, or until the garage door opener is activated.

Once the garage door opener is activated the lights will turn offafter the specified period of time (the

factory setting is4-1/2 minutes).The LIGHTbutton will not control the lightswhen the door is in motion.

The duration ofthe light timing can be adjusted by accessing the menu using the navigation buttons.

Motion Sensor

The motion sensor will automatically turn on the garage door opener lightswhen motion is detected. The

lights will come on for the set period of time, then shutoff.The factory setting ison and setat 4-1/2

minutes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Chamberlain WD962KEV Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info