Bedienungsanleitung Charnwood LA 30iB (Seite 13 von 20) (Englisch)

815488

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Fig. 10 InjectorTee

INSTALLATION INSTRUCTIONS charnwood

Connect the heating system to the boiler ensuring that the

primary flow pipe rises from the fire. Fill the system with

water and check for leaks.

FLUE CONNECTION AND INFILLING

Make the flue connection with the special 150° elbow part no.

010/AV12. Please note that this item is ordered separately

from the appliance. The legs of the elbow may be cut on site

to suit the chimney. Also note that the legs of the elbow are

different lengths to enable some situations to be catered for by

turning the elbow around.

The end of the flue pipe must line up with the centre-line of

the chimney, and must also extend to the point where the

chimney narrows to its final size. Any large voids must be filled

and flaunched to the flue pipe to ensure that all soot deposits

can be cleared when the appliance is swept.

Ensure that the flue pipe is not obstructed or restricted in any

way and that all joints are well sealed.

Before infilling cover the front of the fire to protect it. Ensure

that the flue pipe is central and then fill the space between the

body of the fire and the structural brickwork with vermiculite

(eg. micafil or similar) concrete. Ensure that there are no air

pockets. The recommended mix is six volumes of vermiculite

granules to one volume of Portland cement thoroughly mixed

together. Enough water should be added so that no more than

one or two drops of water are released when a handful of the

mixture is squeezed.

After filling with vermiculite flaunch the top of the flue

connector pipe to the chimney with lime mortar.

Make good the holes in the front and side of the chimney

breast making sure that they are completely airtight. A typical

installation is shown in Fig. 11.

In most installations it will be possible to sweep the chimney

through the appliance. If this is not possible then some

alternative means (such as a soot door), must be provided.

The free-inset method of installation may be used instead of in-

filling. Details are available on request.

FITTING THE FIRE

In some cases it may be necessary to place the connecting flue

pipe in the chimney before fitting the fire into the fireplace.

Apply fire cement to the rear face of the sealing flange on the

appliance. Fit the appliance into the opening ensuring that it is

central and that a good seal is made between the sealing flange

and the face of the surround.

Remove any excess fire cement from around the sealing

flange.

The fire should be screwed to the hearth through the holes at

the base of the sealing flange.

Fig. 9 Typical Central Heating & Hot Water System Using 4

Tappings

Gravity Return 28mm

Gravity Flow 28mm

22mm Open Vents

Cold Water Tank

Overflow

Domestic Hot Water Draw Off

Drain Cock

Indirect Hot Water Cylinder

Central

Heating Flow

Circulating Pump

Central

Heating

Return

Drain Cock at Lowest Point

Minimum Return

Thermostat

Gravity Radiator

Overflow

Feed and Expansion Tank

Injector Tee

Central Heating Return

Gravity Return

(28mm Pipe)

Common Return to Boiler

(28mm Pipe)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Charnwood LA 30iB Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info