Bedienungsanleitung Charnwood LA10 (Seite 9 von 16) (Englisch)

815486

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

HEALTH AND SAFETY PRECAUTIONS

Please take care when installing the stove that the requirements of

the Health and Safety at Work Act 1974 are met.

Some types of fire cement are caustic and should not be allowed to

come into contact with the skin. In case of contact wash with plenty

of water.

If there is a possibility of disturbing any asbestos in the course of

installation then please use appropriate protective equipment.

There must not be an extractor fan fitted in the same room as the

stove as this can cause the appliance to emit fumes into the room.

. Approved

Document J of the building regulations gives more detailed

information.

This stove is capable of intermittent operation.

This stove is not suitable for use in a shared flue system.

In addition to these instructions the requirements of BS.8303 and

BSEN 15287-1:2007 must be fulfilled. Local Authority Bylaws and

Building Regulations, including those referring to national and

European Standards, regarding the installation of Solid Fuel burning

appliances, flues and chimneys must also be observed.

CO ALARMS

Building regulations require that whenever a new or replacement

fixed solid fuel or wood/biomass appliance is installed in a dwelling a

carbon monoxide alarm must be fitted in the same room as the

appliance. Further guidance on the installation of the carbon

monoxide alarm is available in BS EN 50292:2002 and from the

alarm manufacturer's instructions. Provision of an alarm must not be

considered a substitute for either installing the appliance correctly or

ensuring regular servicing and maintenance of the appliance and

chimney system.

There must be an adequate air supply into the room in which the

appliance is installed to provide combustion air. The combustion air

supply must be via a permanently open vent. The requirement for

minimum free area is partly dependent on the design air permeability

of the house. In older properties the air permeability will be above

3 2

5.0m /(h.m ), and there is no statutory requirement for this size of

3 2

stove but in some modern properties if it is less than 5.0m /(h.m ),

2 2

then the minimum free area of vent is 27.5cm (4.3in ). The vent

must be positioned such that it is not liable to blockage

SPECIFICATION

CHIMNEY

HEARTH AND FIRE SURROUND

The nominal output of the LA10 is 4.8 kW (16,300 Btu/h). This

output is based on a 45minute re-fuelling cycle burning seasoned

hardwood logs. The average flue temperature at rated output is

266°C. The Flue gas mass flow is 4.8g/s and the stove weight is

62kg.

In order for the appliance to perform satisfactorily the chimney

height must not be less than 4 metres measured vertically from the

outlet of the stove to the top of the chimney. The internal dimensions

of the chimney should preferably be 175 mm (7 in.) or 200mm (8

in.) either square or round and MUST NOT BE LESS THAN 125 mm

(5 in.).

If an existing chimney is to be used it must be swept and checked, it

must be in good condition, free from cracks and blockages, and

should not have an excessive cross sectional area. If it was previously

used by an open fire then the chimney should be swept one month

after installation to clear any soot falls which may have occurred due

to the difference in combustion between the stove and the open fire.

If you find that the chimney is in poor condition then expert advice

should be sought regarding the necessity of having the chimney lined.

If it is found necessary to line the chimney then a lining suitable for

Solid Fuel must be used.

If there is no existing chimney then a prefabricated block chimney or

a twin walled insulated stainless steel flue to BSEN 15287-1:2007 can

be used either internally or externally. These chimneys must be fitted

in accordance with the manufacturers instructions and Building

Regulations.

Single wall flue pipe is suitable for connecting the stove to the

chimney but is not suitable for using for the complete chimney.

If it is found that there is excessive draw in the chimney then a

draught stabiliser should be fitted.

It is important that there is sufficient draw in the chimney and that

the chimney does not suffer from down-draught. When the chimney

is warm the draw should be not less than 2.5mm (0.10 inches) water

gauge (25 Pa). If in doubt about the chimney seek expert advice.

The stove must stand on a fireproof hearth and must not be situated

closer than 600mm from the sides and 700mm from the rear to

INSTALLATION INSTRUCTIONS

charnwood

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Charnwood LA10 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info