Bedienungsanleitung Charnwood LA20i (Seite 10 von 16) (Englisch)

815487

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

PREPARATION OF FIREPLACE

FITTING THE FIRE

Before fitting the appliance into an existing fireplace remove

the fireback and any loose in-fill material.

The hearth, surround and opening for the appliance must

conform with Figs. 4 and 5. The flat area around the opening

must be a minimum of 750 mm wide and 660 mm high.

Ensure that the hearth and the base in the opening are flat,

level, and at right angles to the surround.

Make a hole in the front of the chimney breast to give access

for infilling and fixing the flue pipe. If the optional boiler is to

be fitted it will also be necessary to make a hole in the side of

the chimney breast to give access for the pipework.

In some cases it may be necessary to place the connecting flue

pipe in the chimney before fitting the fire into the fireplace.

Apply fire cement to the rear face of the sealing flange on the

appliance. Fit the appliance into the opening ensuring that it is

central and that a good seal is made between the sealing

flange and the face of the surround.

Remove any excess fire cement from around the sealing

flange.

The appliance should be screwed to the hearth through the

holes at the base of the sealing flange.

The optional add-in boiler which may be fitted in the

appliance has an output sufficient for domestic hot water

heating. If the boiler is fitted then the room heating will be

reduced.

The hot water system should be a gravity circuit and must be

correctly vented as shown in Fig. 6.

The steel boiler in conjunction with a double feed indirect hot

water storage cylinder to BS:1566 part 1 should be used in

most situations, unless the appliance is to be fitted in a soft

water area in which case the stainless steel boiler may be used

with a direct hot water cylinder.

All pipework in the primary circuit must be 28mm diameter

and the flow pipe must rise continuously from the boiler to

the open vent.

If an indirect cylinder is used then the primary circuit should

be filled with a suitable inhibitor to prevent the build up of

scale and corrosion.

HOT WATER SYSTEM

INSTALLATION INSTRUCTIONS

405 mm

400 mm

Minimum

This Dimension Is The

Minimum Level Area

Required To Enable The

For Overall Sizes Of

Hearth See The

Section Titled "Hearth".

Doors To Be Opened.

Fig. 4. Limiting Dimensions Of Hearth

660 mm

The shaded area on the face of

the surround is the minimum flat

area required.

750 mm

Fig. 5. Limiting Dimensions Of Surround And Opening

Drain Cock at Lowest Point

Drain Cock

Indirect Hot Water Cylinder

Cold Water Tank

Overflow

Feed and Expansion Tank 22mm Open Vents

Overflow

Domestic Hot Water Draw Off

Gravity Return 28mm

Gravity Flow 28mm

Fig. 6. Typical Gravity Hot Water System

charnwood

Dimension A:

Max. 470mm (18 ”)

Min. 405mm (16")

Dimension B:

Max. 575mm (23")

Min. 555mm (21 ”)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Charnwood LA20i Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info