Bedienungsanleitung Charnwood SLX20 (Seite 6 von 20) (Englisch)

815482

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

ASH CLEARANCE OVERNIGHT BURNING

The ashpan should be emptied regularly before it comes too full. The Empty the ashpan, if necessary, then riddle the fire if you are burning

most convenient time to remove the ash is just before riddling the solid fuel. If the fire is very low then it may be necessary to add a

fire since the ash will be at its coolest. Use the ashpan/riddling tool little fuel and turn the thermostat control up to maximum for a brief

provided to remove the ashpan, the fold up carrying handle should period until the fire is burning brightly before filling with fuel. Some

be held with a heat proof glove. experimentation may be necessary to find the setting most suitable

for the particular fuel used and the draw on the chimney, but

Never allow the ash to accumulate in the ashpan so that it comes in

generally the thermostat should be turned down to the minimum

contact with the underside of the grate as this will seriously damage

setting. For overnight burning the fire doors must be closed.

the grate bars. Ensure that the air inlet damper is not prevented from

closing by spillage fuel or ash. To revive the fire, empty the ashpan if necessary, riddle (when

burning solid fuel) and turn the thermostat control to maximum.

Care should be taken to ensure that the ash is cool before emptying

When the fire is burning well load more fuel as necessary and turn

it into plastic liners or bins.

the control knob to the desired setting.

To make ash removal easier there is a special Charnwood ash carrier

available. This may be purchased from you supplier or, in case of THROAT PLATE AND FLUEWAY CLEANING

difficulty, from ourselves. It is important that the throat plate and all the appliance flueways are

kept clean. When burning smokeless fuels they should be cleaned at

RIDDLING

least monthly. When burning other fuels they should be cleaned once

The fire should be riddled with the doors shut. Place the tool on the a week, and more frequently if found necessary.

knob and rotate between the horizontal and the 45° position several

The throat plate and flue ways may be cleaned with a low fire still

times as shown in Fig. 2.

burning. Use the scraper tool to scrape any sooty deposits off the

Caution: when riddling the grate using solid fuel do not go beyond front of the plate until they drop into the fire.

the 45° position as this can cause the grate to jam.

More soot will be deposited on the throat plate and in the flueways if

If jamming does occur then the fire should be allowed to burn for the appliance is run at low levels for long periods. If this is the case

approximately half an hour before riddling the grate again as then more frequent cleaning will be necessary.

described above.

SPECIAL POINTS WHEN BURNING COAL

When loading the appliance take care not to smother the fire.

Instead, fill the firebox in two stages, waiting for the flames to appear

Too much riddling can result in emptying unburnt fuel into the above the fire between each stage.

ashpan and should therefore be avoided. Clinker should regularly be After a period of slumbering always turn the air control up to

removed from the firebed. maximum and wait until flames appear above the fuel bed before

After riddling, the grate should be put back into the solid fuel or opening the doors.

wood position as required (the tool should be horizontal for solid Burning coal will produce more soot deposits than other fuels,

fuel or vertical for wood). especially if the fire is run at low levels for a long periods. Therefore,

please not that some blackening of the glass may occur. It is also vital

REFUELLING

to clean the throat plate regularly, weekly cleaning is recommended.

Keep the firebox well filled (the fuel may be sloped up from the front

fire bars), but do not allow the fuel to spill over the top of the front

fire bars. Take care, especially when burning wood, that the fuel does

not project over the front fire bars or damage to the glass may be

caused when the doors are closed.

Riddling twice a day is usually sufficient when

burning solid fuel. When burning wood, ash should be allowed to

build up and only riddled when the ash begins to cover the slots in

the rear fireplate.

charnwood

OPERATING INSTRUCTIONS SLX20

MU LTI-FUEL

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Charnwood SLX20 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info