767855

Chicco Next 2 Me Forever Seite 20

20
Zoom out
Zoom in
Vorherige Seite
1/139
Nächste Seite
20
21
the height, press the buttons “F1” on the upper short side, and
lift or lower the structure to the desired position (Fig.20). Releas
the button to lock the position.
13. The base of the product can be inclined by adjusting the 2 feet
at different heights.
WARNING: The product can be inclined by a maximum of 4 posi-
tions between one leg support and the other (e.g., right leg in posi-
tion 1 and left leg in position 5).
WARNING: The child’s head must always be positioned near the
raised end (fig.21).
COT CO-SLEEPING CONFIGURATION (FASTENED TO BED)
It is possible to fasten the product to the parents’ bed (co-sleeping
configuration).
WARNING - IMPORTANT FOR YOUR CHILD’S SAFETY: This con-
figuration is allowed only with beds that allow compliancy with all
the conditions described in this paragraph.
In particular, the folding side of the cot must always be positioned
against the mattress of the parents’ bed and the parents’ mattress
must be aligned with (or at most higher than) the height of the cot’s
side (Fig.22A-22B). Moreover, the product must be fastened to the
structure of the parents’ bed or to the mattress support (mesh or
slat sprung base).
WARNING: Check that the structure of the product in co-sleeping
configuration does not interfere with the parents’ bed.
WARNING: Use the product with the side lowered only in co-sleep-
ing configuration.
14. Put the product against the parents’ bed and check its height
compared to the parents’ mattress (Fig. 23).
WARNING: The height of the parents’ mattress must be higher than
or the same as that of the side of the product. If this is not the case,
use the adjustment system to achieve this condition on both sides.
WARNING: In co-sleeping configuration, the 2 feet of the product
must be set at the same height.
15. To fasten the product to the parents’ bed (co-sleeping configura-
tion), use the pair of supplied straps “G”.
16. Now fasten the grey buckles “G1” to the safety straps “D4” and
pull them as tightly as possible (Fig. 24).
17. Then pass the straps “G” around the parent’s bed frame/slats
from top to bottom. Complete the bed fastening operation by
hooking the and length adjustment prongs “G2” to the grey bed
fastening buckles “C1”, located under the base of the product
(Fig. 25) until a loop is formed (Fig. 26). Make sure to repeat the
step on both sides. To make installation easy, when fastening the
buckles, always keep the product slightly away from the parents’
bed.
18. Now pull the product completely to the parents’ bed, tighten
the loop by pulling the straps “G” (Fig. 27) and make sure that the
safety straps “D4” of the folding side barrier are fully tensioned.
Carry out this step first on one side and then on the other, ad-
justing the straps until the product is in contact with the parents’
mattress.
WARNING: If the straps “D4” are not fully tensioned, it is not possible
to maintain the safety height of the side.
19. Lower the side of the product by pushing button “D1” (Fig. 28)
and accompanying the side until it reaches the end of its travel.
20. Lock all wheels with brake “A5” (Fig. 29).
21. To close the side “D1”, simply lift it upwards, holding it from the
centre. Always make sure that it is engaged correctly.
WARNING: Before use, always make sure that there is no space
between the parents’ mattress and product’s side. Otherwise adjust
the straps “G” pulling them until the required condition is restored.
Make sure that the side is always free to be lowered and raised com-
pletely.
WARNING: If when fastening the product to the parents’ bed it is
not possible to fit the product’s feet under the parents’ bed, the bed
can be fastened anyway by the following the instructions above
folding the feet “A3” with the release button “A4” when putting the
product against the bed.
WARNING: Whenever the side is lowered, make sure that the posi-
tion compared to the parents’ mattress has not changed from that
illustrated in the paragraphs above.
WARNING: When the product is used in “Co-sleeping configuration
(fastened to the bed),” it must always be mounted on the long side of
the bed. DO NOT install the product at the head or feet of the bed.
MAKING THE PARENTS’ BED
When in “Co-sleeping configuration (Fastening to the bed)” to fa-
cilitate the daily making of the parents’ bed, you can unfasten the
product from the bed. Just list the folding side barrier “D” completely
and unfasten the grey buckles underneath the base of the product.
When fastening the product again to the parents’ bed, pull the
straps back to the maximum tension to ensure that the product is
correctly and securely fastened to the parents’ bed. Make sure that
all the steps illustrated above in “Co-sleeping configuration (fas-
tened to the bed)” have been completed.
HOW TO USE THE COT
22. If previously used in co-sleeping configuration, remove the
product from the bed by unfastening the buckles of the straps
“G”, taking care to accompany the safety straps “D4” of the fold-
ing side barrier “D”.
23. WARNING: If the feet “A3” were folded, straighten them again until
you hear the fastening click. Repeat the step on the other leg as
well (Fig. 30).
24. Check the fastening of the folding side barrier to the structure,
after its automatic ascent.
WARNING: Remove the straps from the parents’ bed and keep
them in a place out of the child’s reach.
HOW TO USE THE FLOOR BED FOR TODDLERS
25. To use the product in this configuration, remove the legs “A” as
shown below:
- Tilt the product on the short side, taking care to place a protective
sheet on the floor.
- Pull leg “A” to the maximum extension until it reaches the safety
lock (Fig. 31), act on the safety pin, positioned on the rear leg (Fig.
32) and pull the leg completely out of the product. Repeat this
operation on the other side as well.
26. Keeping the product in an upright position, proceed as indi-
cated below to fold and remove the side:
- Pull the safety strap “D4” of the folding side barrier “D” until it is fully
extended and attach it to the buckle “C1” at the rear of the base “C”
as shown in Figures 33 and 34. Repeat the step for the other side.
- Position the product again on base “C” and press button “D1” to
lower the side (Fig. 35).
- Open the zipper on the fabric on the side (Fig. 36) with the help of
a paper clip and fold the fabric over so that the horizontal tubular
element is uncovered (Fig. 37).
- Press button “D3” on the side cart and simultaneously lift the bar
upwards to release it from the product (Fig. 38). Repeat this step
on the other side.
WARNING: Once removed, keep the bar out of the child’s reach.
- Fit the fabric of the side under the mattress again (Fig. 39).
CARE AND MAINTENANCE
The product crib and mattress have a fabric lining that can be re-
moved completely and washed except for folding side barrier “D”.
To remove the fabric, follow the instructions in the paragraph “RE-
MOVING THE FABRIC.”
WARNING: Covering or removing the fabric may take a few min-
utes and must be carried out by an adult.
Regularly inspect the product for signs of wear and damage. In the
case of damage, do not use and keep out of reach of children.
Do not use solvents, abrasive or overly aggressive products.
When washing the fabrics pay close attention to the instructions
on the label.
Maximum washing temperature 30°C
Do not bleach
Do not tumble dry
Do not iron
Do not dry clean
Line drying
Check that the fabric and the stitching are in good condition after
… 20 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Chicco Next 2 Me Forever wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info