Bedienungsanleitung Christopeit AF1 - 1129 (Seite 17 von 48) (Deutsch, Englisch, Holländisch, Französisch)

644077

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

English

Step 3:

Attach the support (15) at the main frame (1).

1. Place the lower end of the support (15) against the main frame (1)

and plug the ends of the two computer cable harnesses (40) and (41)

projecting from (1) and (15) together. (Note: The connection cable (41)

projecting from the support (15) must not slide into the tube, as it is

required for later steps of installation.)

2. Connect the middle section tension cable (42) to the bracket of lower

section cable tension (39) (See ﬁgure A1-A3). Before this step of the

installation, it is advisable to adjust the resistance setting to the position,

at which the cable extends furthest from the sheath. Put the lowest part

of cable (42) into the small hook of lower tension cable (39) (ﬁgure A1).

Pull it until the small hook get in higher position (ﬁgure A2) and then

insert the cable (42) onto the bracket (39) (ﬁgure A3). When joining the

tubes, ensure that the cable connection is not trapped.

3. Put one spring washer (5) and one washer (6) on each screw M8x15

(25). Push the screws (25) through the holes in the support (15), screw

into the threaded holes of the main frame (1) and tighten them ﬁrmly.

Step 4:

Attach the foot tube left and right (28+30) at pedal crank (70).

1. Push the end of the right pedal tube (30) onto the pedal crank (70) and

tighten it with screw M8x20 (24), washer (23) and spring washer (5) at

the pedal crank (70) ﬁrmly.

2. Push the pedal bracket right (49) into the holder of right foot tube (30)

and tighten it with screws M8x15 (25), screw M8x20 (24), steel plate for

pedal (31), spring washer (5), washer (6) and plastic washer (23) ﬁrmly.

3. Install the left pedal tube (28) with all additionally required parts on the

left hand side of the machine as described in 1. + 2.

Step 5:

Attach the connection tube L&R (21+27) and pedal bracket L&R (44+49).

1. Push the axle support (16) centrally into the tube welded crosswise to

the handlebar post (15).

2. Push on the connection tube right (27) from the right hand side and the

connection tube left (27) from the left hand side.

(Note. After installation, the threat for hand grips at connection tubes

should be in a manner of front direction).

3. Push one spring washer (5) and one washer 8//28 (23) onto each screw

M8x20 (24), screw the screws (24) into the threaded holes at both ends

of the axle support (16) and tighten ﬁrmly.

4. Put the ends of pedal bracket left and right (44+49) into the bottom

holder of connection tube left and right (21+27), so that the holes are

aligned. Push the pedal bracket shaft (94) from inside through the holes

of connection tube (21+27) and pedal brackets (44+49) to outside.

Secure them with screw M8x25 (4) washer (6) and spring washer (5).

(This connection point has to move easily)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Christopeit AF1 - 1129 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info