Bedienungsanleitung Christopeit CPS2 (Seite 15 von 48) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

662743

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Step 4:

Installation of the saddle support (49) on the main frame (1) with the

saddle support screw (47).

1. Push the saddle support wrapping (43) onto the saddle support (49).

Insert the saddle support (49) into the provided holder of the main

frame (1) and secure at the desired position by screwing in the saddle

support screw (47).

(Note: To screw in the saddle support screw (47), the threaded hole in

the main frame (1) and one of the holes in the saddle support (49)

must be aligned. Furthermore, ensure that the saddle support (49) is

not pulled out of the main frame beyond the marked maximum

adjustment position. The setting of the saddle support can be adjusted

as desired later.)

Step 5:

Connecting the computer cable harness incl. sensor (45) to the

computer cable harness (54), connection of the cable of the resistance

adjuster (38) with the resistance adjusting unit (36) and installation of

the handlebar support (25) on the main frame (1) with the round-headed

Allen screws M8x15 (55), washers 8//20 (19) and spring washers for M8

(72).

1. Place the lower end of the handlebar support (25) against the main

frame (1). Plug the ends of the two computer cable harnesses (45) and

(54) projecting from (1) and (25) together.

2. When the cable connections have been made, push the cable (38) from

the bottom through the handlebar support (25) and pull out of the opening

at the upper end of the tube. Then push the handlebar support (25)

onto the main frame (1).

(Note: When joining the tubes, ensure that the harness and cable

connections are not trapped.

3. Put one spring washer and one washer on each screw. Push the screws

through the holes in the support, screw into the threaded holes of the

main frame (1) and tighten firmly.

4. Join the two ends of the cables (36) and (38) as indicated in the drawing

below (A+B).

(Note: Before this step of the installation, it is advisable to adjust the

resistance setting to the highest stage, at which the cable extends

furthest from the sheath.

If the factory adjusted pedal resistance range of the machine should

later be found to be too great or too small, this can be simply adjusted

as the cables. For this, loosen nut of cable (38), turn the threaded piece

correspondingly and secure the new position with nut. In this respect:

The further is screwed into the U-piece, the greater the resistance, and

the converse.)

When the connection has been made, insert the resistance adjusting

unit (36) into the opening of the handlebar support (25) and secure with

screw (35).

Step 6:

Installation of the handlebar (40) on the handlebar support (25) with

the carriage bolt M8x90 (57), the spring washer for M8 (72), the was-

her 8//20 (19) and the handgrip nut (62).

1. Place the handlebar (40) against the handlebar support (25) and adjust

so that the hole patterns in the handlebar and the handlebar support

are aligned. Put the screw (57) into the hole, push the washer (19) , the

spring washer (72) on screw end and tighten firmly with the handgrip

nut (62).

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Christopeit CPS2 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info