Bedienungsanleitung Christopeit CXT 7200 (Seite 18 von 32) (Deutsch, Englisch)

793034

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite



Remove all the separate parts from the packaging, lay

them on the oor and check that all are there on the

basis of the assembling steps. Please note that a num-

ber of parts have been connected directly to the main

frame and preassembled. In addion, there are seve-

ral other individual parts that have been aached to

separate units. This will make it easier and quicker for

you to assemble the equipment. Assembly me ap-

prox. 60min.





Aach the front foot (45) with preassembled trans-

portaon roller (44+46) to the main frame (40).

Do this with the two screws M8x55 (41), washers

8//16 (28) and self-locking nuts M8 (43).

Aach the rear foot (55) with preassembled height

adjustable screw (57) to the main frame (40). Do

this with the two screws (41), washers (28) and self

locking nuts (43). Aer assembly has been completed,

you can compensate for minor irregularies in the

oor by turning the foot screw (57). The equipment

should be set up that the equipment does not move

of its own accord during a training session.



       -



Place screws M8x16 (32), washers 8//16 (28), cur-

ved washers 8//19 (33) and spring washers for M8

(27) accessibly beside the front part of the main

frame (40).

Place the lower end of the support (8) against the

main frame (40) and plug the ends of the two com-

puter cable harnesses (2+39) projecng from (8+40)

together. (Note: The computer cable harness (2)

projecng from the support (8) must not slide into

the tube, as it is required for later steps of installa-

on.) When joining the tubes, ensure that the cable

connecon will not trapped.

 Put one spring washer (27) and one washer (28)

or curved washer (33) on each screw (32). Push the

screws (32) through the holes in the support (8),

screw into the threaded holes of the main frame (40)

and ghten rmly.







 Put the le footrest holder (103) at the pedal crank

(91) on le hand side and ghten the footrest holder

(103) with washers 8//22 (14), spring washer for M8

(27) and screw M8x20 (99) rmly. Put the screw cover

(98) onto the footrest holder (103).

2. Push the connecon tube cover (31) onto le con-

necon tube (34) into intended posion and ghten

with screws M5x12 (5).

 Install the right footrest holder (100) incl. all

addionally required parts on the right hand side of

the machine as described in 1. – 2.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Christopeit CXT 7200 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info