Bedienungsanleitung Ciclo CM 628 Master (Seite 8 von 16) (Englisch)

588917

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

To set the needed values for the

calculation press left button short:

Heart rate lower limit

Adjust with right and left button (save and continue with

left button)

Default setting – 100 bpm (beats per minute) or with

CICLO

IInnZone® calculated value.

Range: 20 – 240

A lower heart rate limit can be set here or (after

CICLO

IInnZone®-calculation) the calculated value is

shown.

When the actual heart rate is lower than this value, the

CM 628 gives an optical alarm (display shows blinking

heart rate with 'lo' = low).

Heart rate upper limit

Adjust with right and left button (save and continue with

left button)

Default setting – 160 bpm (beats per

minute) or with

CICLO

IInnZone®

calculated value.

Range: 20 – 240

An upper heart rate limit can be set here or (after

CICLO

IInnZone®-calculation) the calculated value is

shown.

When the actual heart rate is higher than this value, the

CM 628 gives an optical alarm (display shows blinking

heart rate with 'Hi' = High).

Maximum heart rate

Adjust with right and left button (save

and continue with left button)

Default setting – 190 bpm (beats per

minute) or with

CICLO

IInnZone®

calculated value.

Range: 30 – 240

Shows the maximum heart rate, calculated with

CICLO

IInnZone®.

Fitness level

Set with right button, save and

continue with left button.

Range 1-4, corresponding to the

following levels:

1 – poor fitness

2 – average fitness

3 – good fitness

4 – high fitness

48 49

Start the transmitter search in the CM 628 by

pressing both buttons for a short time.

A percentage value runs up in the

display during the initialisation.

In case of successful initialisation,

the CM 628 changes automatically

into the normal operating mode and the indication SPD/AV

appears in the display.

In case of unsuccessful initialisation,

the transmitter search can be

started again by repeated short

pressing of both buttons.

The initialisation is interrupted after

a fault by short pressing of the left button and the CM 628

then likewise changes into the normal operating mode.

Pay attention during the initialisation that no second

cadence transmitter is located nearby (currently active).

4.6 Calculation of

CICLO

IInnZone® , setting of the

heart rate limits /fitness level /sex / weight / year of

birth and initialisation of the heart rate transmitter

Press the right button until the

following display appears:

By pressing the left button for 3 sec.,

this display now appears:

By pressing both buttons short simultaneously the

CICLO

IInnZone®-calculation is started (see Chap. 7

CICLO

IInnZone®).

N.B.: when the CM 628 is used for the first time, the

CICLO

IInnZone® function should not be started at

once, since in order to obtain an exact calculation it is

necessary to insert the personal data relative to sex, weight

and age (these values are also necessary for calculation of

the calorie consumption).

After setting these values, the

CICLO

IInnZone®-

calculation can be started (see page 51).

02 CM 628 englisch 34-65 19.05.2005 10:23 Uhr Seite 16

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ciclo CM 628 Master Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ciclo CM 628 Master

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info