Bedienungsanleitung Ciclo CM 8.3 A Master (Seite 5 von 11) (Englisch)

588920

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

For a better reading in the following chapters the setting modes are fat

printed and the settings fat and italic.

SET ALT / SET HOEHE

To define altimeter settings.

To select, press the centre button.

ALTITUDE / HOEHE

To change current altitude.

Range: -300 to +6000 m and/or ft

Set with right and left buttons, continue with left button.

Here you can change the altitude that is displayed, e.g. if you notice that

the current altitude diverges from altitude shown in the display (e.g. if

barometric pressure changes).

HOME OFF / HEIM AUS

To switch the home altitude on/off.

Default: OFF

Set with right button, continue with left button

Here you can switch the automatic reset off the home altitude value

on/off

HOME ALT / HEIMHOEHE

Starting value for altimeter.

Range: -300 to +6000 m and/or ft

Set with left or right button, continue with left button

CM 8.3A has a barometric altimeter which adapts itself to temperature

variations.

Changes of barometric pressure (e.g. during the night) can cause

variations of the indicated altitude in the display. To compensate for

these variations you can set the altitude of your origin (e.g. starting

point such as home).

With each reset of the daily values (deletion) and starting a new recor-

ding (chap. 7) the current altitude will be reset to the adjusted altitude.

UNIT m

Set unit of measurement for altitude.

Default: m (meters)

Here you can select whether the indication is meter (m) or feet (ft).

UNIT °C

Set unit of measurement for temperature.

Default: °Celsius

Here you can adjust whether the indication is Celsius (C) or Fahren-

heit (F).

SET BIKE1 / SET RAD1

Adjustment of bike-specific values, e.g. total distance, circumference,

unit and more for bike 1.

Choose with centre button.

To do these settings for bike 2, press right and left button short simulta-

neously in normal mode. CM 8.3A switches to bike 2, then enter again

setting mode (display then shows SET BIKE2/SET RAD2).

DAY DST / TAGES-DST

Adjustment of the daily distance.

Default: 000.00 km

Range: 000,00 to 999,99 km or m

Set with right and left button, store with left button.

Here the daily distance can be adjusted, e.g. the point of starting a tour,

when using a printed tour-guide.

(This setting doesn’t change the total distance. Only really ridden kilo-

metres are counted).

TOT DST / GES. DST

Adjustment of the total distance.

Default: 0000 km

Range: 0 to 99999 km or m.

Set with right and left button, store with left button.

Here the total distance can be adjusted.

Wheel/Radumf.

Adjustment of circumference

Default: 2080 mm

Range: 0000-3999 mm

Set with right and left button, store with left button.

Here the circumference can be adjusted.

Size Circumference

40-559 26 x 1,5 2026 mm

44-559 26 x 1,6 2051 mm

47-559 26 x 1,75 2070 mm

50-559 26 x 1,9 2026 mm

54-559 26 x 2,00 2089 mm

57-559 26 x 2,125 2114 mm

37-590 26 x 1 3/8 2133 mm

32-620 27 x 1 1/4 2199 mm

40-622 28 x 1,5 2224 mm

47-622 28 x 1,75 2268 mm

40-635 28 x 1 1/2 2265 mm

37-622 28 x 1 3/8 2205 mm

20-622 700 x 20C 2114 mm

23-622 700 x 23C 2133 mm

25-622 700 x 25C 2146 mm

28-622 700 x 28C 2149 mm

32-622 700 x 32C 2174 mm

The circumference of the wheel can be taken from the chart

(Pict. G) or be measured by yourself.

Measuring the circumference of the wheel (for a more precise setting):

Put a marking at the front-tire and on the ground (e.g. with chalk). Ride

straight ahead exactly one turn of a tire (for a very exact measurement,

check the pressure of the tire before getting on your bike) and mark this

position on the ground. Now measure the exact circumference of the

wheel between the two markings at the ground (in mm) – see pict. F.

Unit km bzw. Unit mi

Adjustment of the measuring unit (kilometres or miles).

Default: km

Set with right button, store with left button

Here you can choose whether the display should show kilometres

(km/h) or miles (m/h).

SPD INISCAN

To start this function, simultaneously press the left and right buttons

briefly, jump setting with left button.

To initialize the speed transmitter (for first use or after battery/trans-

mitter change):

First, activate the speed transmitter (by moving the magnet close to

the transmitter where marked) then press the left and right buttons

simultaneously. A percentage will be displayed in the upper display. If

transmitter has been initialized successfully, the next setting option will

be displayed.

If transmission could not be initialized (e.g. transmitter was not activa-

ted) “error” will be displayed in the upper display. By pressing the left

and right buttons simultaneously the search for the transmitter will be

started again. To jump this setting press left button.

Indication: If the transmitter has already been initialized for Bike1 it

can not bee initialized for Bike 2 at the same time. To switch to Bike 2

you have to “delete” the initialization of Bike 1 (this can take place by

initializing the transmitter search for Bike 1 without switching on the

transmitter; “error” will be displayed – or by the reset/delet function

in the adjusting mode, but be carefull because there will be deleted all

values and adjustments also).

CAD OFF/TRITT AUS

Switch cadence on/off (ON/AN – OFF/AUS).

Default: OFF/AUS

Set with right button, store with left button.

Here you can switch on/off the cadence measuring. To use this function

you need the optional cadence-set (available at your local dealer).

Ciclo CM 8.3 A Master Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ciclo CM 8.3 A Master

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info