Bedienungsanleitung Ciclo HAC 4000 (Seite 4 von 15) (Englisch)

588930

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

2.5 Attaching the HAC

to the handlebar bracket

(the HAC must be attached to the handlebar bracket in

order to be used as a bike computer)

Remove the HAC from the wristband through turning

counter-clockwise. Insert it in the handlebar bracket and turn it

clockwise until it engages.

To check if the HAC has been attached correctly, please

turn the wheel a couple of times to see if the computer receives a

signal.

Last, but not least, pull the cable-ties of the speed transmitter tight

and cut off what is too long.

To remove the HAC from the handlebar bracket, turn it

counter-clockwise.

3. USING THE BUTTONS

The HAC display is divided into two parts: an upper part

and a lower part. One function is shown in each area, so that two

functions can be read simultaneously. This way the possible func-

tions on the displays can be combined as desired.

The two upper buttons are for the functions in the upper display, the

two lower buttons are for the functions in the two lower displays.

The following applies: The right button calls up main functions, the

left button calls up the accompanying sub-functions.

The buttons are abbreviated as follows in the operating instructions:

Upper Right button: UR-button

Lower Right button: LR-button

Upper Left button: UL-button

(this button can be used to increase values = Plus-button)

Lower Left button: LL-button

(this button can be used to decrease values = Minus-button)

Start/Stop-button:

The functions stopwatch and count-

down can be started/stopped by

short pressing the start/stop-button

(while depending function is shown in

the display).

Short pressing means 1 second

pressing, long pressing means 4 or

6 seconds pressing (as specified).

Every button press raises a short

signal tone.

4. BASIC SETTINGS

The HAC has two setting modes (these will be called mode

1 and mode 2 in the following instructions). To switch to setting

mode 1, press the UR-button for 4 seconds. To switch to setting

mode 2, press the LR-button for 4 seconds. In order to quit a

setting mode premature, press either the UR- or LR-button again for

4 seconds.

The following applies to both setting modes:

- Pressing the respective button (mode 1: UR; mode 2: LR) swit-

ches from one setting to the next setting.

- The UL-button and the LL-button change the settings (the UL-

button increases, the LL-button decreases) and shifts or switches

off.

If UL- or LL-button are pressed longer than 1 second, the value

changes faster.

4.1 setting mode 1

Press the UR-button for 4 seconds:

AH – Altitude Home (Primary setting

for altitude measurement)

Set with the UL- or LL-button

Standard value = „----“

Setting range min. = -200m or ft x10;

max.= 9000 m / 2952 ft x10

The HAC is equipped with a barometric altitude measure-

ment which automatically adjusts to changes in temperature,

however it may show a variation due to changes in the air-pressure

(e.g. during the night). In order to compensate these variations, you

may set an altitude when starting (e.g. your home, if you always start

out from there), which the HAC uses when you start a new

training round (recording). This setting should be changed if you start

from somewhere else (e.g. vacation). If the setting is not adjusted

(display „----“), the HAC uses the actual (displayed) altitude

when you start a new recording.

PC – PC-transmission mode

Start with UL- and LL-button short simultane-

ously

By pressing UL- and LL-button short simulta-

neously the transmission to the pc is started

(for this you need the interface HACtronic

– an optional accessory ).

During the transmission the lower display counts from 0 to 100%.

PC-Interval – Set memory interval

Set with the UL- or LL-button

Standard value = 20 sec.

Setting range = 2, 5, 10 or 20 sec.

Here the memory interval, in which the

HAC stores data for the pc evaluation (2, 5, 10 or 20 se-

conds) can be adjusted. The maximum recording time is depending

on this interval (2/5 sec. interval = nearly 6 hours recording time, 10

sec. interval = nearly 12 hours recording time and 20 sec. interval =

nearly 24 hours recording time), see also chap. 6.1.

CI 1 – Circumference Bike 1

Set with UL- or LL-button

Standard value = 2080mm

Setting range min. = 500 mm,

max. = 3000 mm

URUL

LRLL

Start/Stop

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ciclo HAC 4000 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ciclo HAC 4000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info