Bedienungsanleitung Ciclo HAC 4000 (Seite 12 von 15) (Englisch)

588930

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

Clock alarm

(see setting mode 2, chap. 4.2)

The time for the clock alarm can be set in

setting mode 2. When this time has been rea-

ched, a signal tones 20 sec. (to premature turn

off the signal press any button).

The clock alarm is switched on/off in set-

ting mode 2, function ‚CA‘.

Heart rate / Cadence graphics (Bargraph)

(depends on the setting in setting mode 2 –

Hr or C)

When used for heart rate:

The HAC4000 has a coloured graphic in the

middle of the display (7 blue boxes and 2 red

boxes). If the current heart rate reaches the set lower heart rate limit,

the first (left) blue box turns black. Depending on the intensity of the

current heart rate, all blue boxes turn black from left to right. If the

current heart rate is above the set upper heart rate limit, the two red

boxes will also turn black, to show that your heart rate is out of the

limit.

This graphic helps you to control your heart rate, even when upper

or lower display show other functions.

When used for cadence:

Shows a black graphic in the middle of the display (9 black boxes).

If the current cadence reaches the set lower cadence limit, the first

(left) black box turns blue. Depending on the intensity of the current

cadence, all black boxes turn blue from left to right. If the current

cadence is above the set upper cadence limit, the two right boxes

will turn red, to show that your cadence is out of the limit.

This graphic helps you to control your cadence, even when upper or

lower display show other functions.

Heart rate alarm

The heart rate alarm is activated/deactiva-

ted by pressing UL-button for 4 sec. Display

shows the symbol , if activated.

Activated heart rate alarm: a signal tones if the

current heart rate is above or below the set

heart rate limits.

Battery warning signal

If the battery power of the HAC is

lower than 2,8 V, display shows ‚bat low’

every 5 sec.

Battery should then be changed.

Power-saving mode

(Power down mode, see setting mode 1,

chap. 4.1)

The HAC can be switched into pow-

er-saving mode, i.e. the display will go blank,

however it retains all stored data (apart from

time and date). This mode is appropriate e.g.

when changing the battery, or when the HAC is not used

for a longer period.

To switch the HAC into the power saving mode, choose

function ‚Pd’ in setting mode 1. Then press UL- and LL-button short

simultaneous.

To leave the power saving mode, press any button.

6. SPECIAL FUNCTIONS

6.1 Information memory function (recording)

Important: For the HAC 4000 to calculate and indicate all

values (and store them for the pc evaluation), a recording

must be started (see below).

The HAC can store information from max. 120 hours

training (when memory interval is set to 20 sec.). For this a recording

must be started (by pressing UL- and LL-button simultaneous for 4

sec.). During this recording all important information such as heart

rate, altitude, temperature, cadence, time, speed, output and travel-

led distance are stored in short intervals (every 2, 5, 10 or 20 sec.,

interval chosen in setting mode 1). This information can be trans-

mitted to a PC (with the – optional available – interface HACtronic

and its programs).

On the PC you can show these data e.g. on graphics, make an eva-

luation, print statistics and so on.

The memory is a ring buffer, i.e. if it is full, it starts from the beginning:

the first stored tour is overwritten, then the second and so on.

When a recording is started, the symbol ’ ’ starts blinking in the

lower display and blinks until the recording is stopped manually – by

pressing again UL- and LL-button simultaneous for 4 sec. (or stops

automatically, see below).

When a recording is started, all minimum, maximum, average and

daily values are set to 0 and current altitude changes to the value set

by ‚AH‘ (altitude home, see setting mode 1; if AH is not set, current

altitude remains unchanged).

The tours stored in the memory can‘t be deleted, they can only be

overwritten by new tours.

Note: All minimum, maximum and average values (displayed

as MIN / MAX / AV), except average and maximum speed,

and all daily values (DAY,) except daily travelling time and

kilometres, are only calculated when the recording is started.

If the recording is not started at the beginning of the current training,

the display doesn‘t indicate the current values – it indicates the

values of the last (recorded) training.

In order to save memory space and battery, the recording stops

automatically after a certain period (e.g. 24 hours when memory

interval is set to 20 sec.).

Total memory time and max. recording time:

2 sec. intervall – total 12 hours, each tour max. 5:59 hours

5 sec. intervall – total. 30 hours, each tour max. 5:59 hours

10 sec. intervall – total 60 hours, each tour max. 11:59 hours

20 sec. intervall – total 120 hours, each tour max. 23:59 hours

6.2 Heart rate/ time manager (HTM)

The HTM is turned on/off in the setting mode 2 (see chap. 4.2 ).

To start/stop the HTM press short start/stop-button when display

shows countdown function (in the lower display).

In order to use the HTM the following values must be entered in the

setting mode:

Upper and lower heart rate limit 1

Upper and lower heart rate limit 2

Countdown 1

Countdown 2

The HTM allows an interval training in 2 consecutive time intervals

(Countdown 1 and 2) and with 2 different heart rate limits (heart rate

limit 1 and 2).

Example:

Set values:

Lower heart rate limit 1 = 120

Upper heart rate limit 1 = 160

Countdown 1 = 30 min.

Lower heart rate limit 2 = 80

Upper heart rate limit 2 = 120

Countdown 2 = 5 min.

Ciclo HAC 4000 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ciclo HAC 4000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info