Bedienungsanleitung Ciclo HAC 5 (Seite 35 von 38) (Englisch)

588931

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

Version

0.0061

PC Connect

033751

ID-Code

9. PC-mode

Before communication of the HAC5 with the computer can begin, the according programs (at least

one) and the interface (with the help of the driver) have to be installed.

9.1 Installation of the interface

Note: before you install the interface driver, please close all other programs and also deactivate the

antivirus scanner of your system, if not, problems may occur.

Plug interface directly into the computer or laptop (if a USB-Hub or multiple plug is used, problems

may occur).

With newer Windows systems, the plug will be automatically recognized and the hardware assistant

starts. Please follow the instructions and insert the CICLO-CD. After installation is completed, the

hardware assistant may appear again (e.g. under Windows XP), in that case please follow the ins

tructions on the screen once again. (Should no automatic installation take place, please look to the

point “problems” below).

If the installation is completed successfully, please check in the device manager of your system by

the point “ports” (COM and LTP) or “ports”. This is where the interface should be seen as “USB

serial port” (or similar). An appointed Com-port will appear next to this in brackets. This Com-port is

needed later for the transfer, please note.

Problems:

Should the interface not be shown under “ports” please check if there is an exclamation or question

mark somewhere (possibly, it is shown as “unknown tool” or “USB-serial’). Double-click on the excla-

mation- or question mark, then install the driver (from the CICLO-CD) again.

9.2 Program installation

After successful installation of the interface, the desired program needs to be installed. In order to do

so, enter the CICLO-CD and double click the desired program. To install, please follow the instruc-

tions on the screen.

After installation open the program:

CICLOtour: adjust the corresponding port (which was shown in the tool manager) in the settings.

In the case that also other devices – like the HAC4 (PRO) or CM4XXM – should be imported, select

“confirm” in the device selection box. CICLOtour will ask you upon beginning the transfer for confir-

mation of the device type.

Click “save” at the right bottom, and then “OK” on the left.

HACtronic: adjust the corresponding port (which was shown in the tool manager) in the settings of

the HACtronic.

In the case that also other devices – like the HAC4 (PRO) or CM4XXM – should be imported, select

“confirm” in the device selection box. CICLOtour will ask you upon beginning the transfer for confir-

mation of the device type.

9.3 Transfer stored tours

To transfer the stored tours of the HAC5 into the pc, press the MR-button for 3 sec (main setting

mode). Select “PC-connect” with the UR-/OR-button and confirm with the MR-button. The display

now shows the version number in the upper display and the device ID in the lower display.

Now attach the interface clamp to the HAC5 in such a way that the contacts of the clamp are sitting

on the contacts of the backside of the HAC5, afterwards put down the HAC5 with the clamp in such

a way, that the display points upwards.

The transfer starts automatically by the program CICLOtour or HACtronic, when you click to the clo-

ck-icon in the icon list (or click to “data” and choose the transmission to the PC).

The program now shows the transfer screen and “wait”. After a few seconds the transfer should start

(do not move the HAC5 during transfer), if not, see below the point “problems”.

When the transfer is done, the program shows all transferred data in a list (raw data window).

Now take off the interface clamp, the HAC5 still shows the transfer display. Press the MR-button

shortly to leave the PC mode.

Note: Once the PC data transfer display is shown, the setting mode cannot be quit prematurely by

pressing the MR-button for 3 seconds. To quit, press MR-button short. Also, from this mode is no

automatic return to the operational mode, it must always be left manually.

Problems:

Should the PC data transfer not start automatically, click‚ “Cancel” in the program, remove the

interface from the HAC and attach again. Then start again the transfer in the program. The transfer

cannot begin automatically if the interface clamp doesn’t sit properly, so please make sure that the

contacts sit properly on the contacts of the HAC5.

Should the transfer be cancelled in the program with a notification of error, the clamp must be remo-

ved and – before a new transfer is started – the pc data transfer display must be left by short pres-

sing of the MR-button and re-selected by pressing the MR-button again. Then re-attach the clamp

and start again the data transfer on the PC.

Installation of the

interface

Program installation

Transfer stored tours

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ciclo HAC 5 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ciclo HAC 5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info