Bedienungsanleitung Cisco 815 (Seite 20 von 28) (Englisch)

605005

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

9 Perform Initial Configuration

This section provides the procedures for performing the initial configuration of your Cisco 815 integrated services router.

Configure the Router Using Cisco Router and Security Device Manager

Cisco Router and Security Device Manager (Cisco SDM) is a web-based configuration tool that allows you to configure LAN

and WAN interfaces, routing, Network Address Translation (NAT), firewalls, VPNs, and other features on your router. If Cisco

SDM is installed on your router, configure the router by following the instructions in the Cisco Router and Security Device

Manager Quick Start Guide. If this document was not shipped with your router, you can obtain Cisco SDM and instructions

for installing it on your router from the following location:

http://www.cisco.com/go/sdm

Note To obtain the Cisco SDM release notes, and other Cisco SDM documentation, go to http://www.cisco.com/go/sdm and

click the Technical Documentation link.

Setting Up the Initial Configuration Using the Setup Command Facility

This section shows how to use the setup command facility to configure a hostname for the Cisco 815 integrated services router,

to set passwords, and to configure an interface for communication with the management network. If the following messages

appear at the end of the startup sequence, the setup command facility has been invoked automatically:

--- System Configuration Dialog ---

At any point you may enter a question mark '?' for help.

Use ctrl-c to abort configuration dialog at any prompt.

Default settings are in square brackets '[]'.

Would you like to enter the initial configuration dialog? [yes/no]:

The setup command facility prompts you for basic information about your Cisco 815 integrated services router and network,

and it creates an initial configuration file. After the configuration file is created, you can use the CLI or Cisco Router and

Security Device Manager (Cisco SDM) to perform additional configuration.

The prompts in the setup command facility vary with the installed interface modules and the software image. The following

example and the user entries (in

bold) are shown as examples only.

For help with interface and port numbering, see the “Interface Numbering” section on page 17.

Note If you make a mistake while using the setup command facility, you can exit and run the setup command facility again.

Press Ctrl-C, and type setup at the privileged EXEC mode prompt (Router#).

Step 1 To proceed using the setup command facility, enter yes when the power-up messages have ended.

Would you like to enter the initial configuration dialog? [yes/no]: yes

Note If these messages do not appear, Cisco SDM and a default configuration file were installed on the router at the

factory. To use Cisco SDM to configure the router, see the “Configure the Router Using Cisco Router and

Security Device Manager” section on page 20.

Step 2 When the following messages appear, press Return to enter basic management setup:

At any point you may enter a question mark '?' for help.

Use ctrl-c to abort configuration dialog at any prompt.

Default settings are in square brackets '[]'.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cisco 815 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cisco 815

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info