Bedienungsanleitung Clarion CMV1 (Seite 35 von 44) (Englisch)

580505

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

CMV1

English

7. SYSTEM SETTINGS

Audio Settings

You can adjust a audio effect or tone quality to

your preference.

● Adjusting the bass

2-1. Select “Bass”.

3-1. Press the [ENTER] button.

3-2. Turn the [UP/DOWN] knob to adjust the

gain from –7 to +7 (The factory default

setting is “0”).

3-3. Press the [RETURN] button to return to the

previous mode.

● Adjusting the treble

2-1. Select “Treble”.

3-1. Press the [ENTER] button.

3-2. Turn the [UP/DOWN] knob to adjust the

gain from –6 to +6 (The factory default

setting is “0”).

3-3. Press the [RETURN] button to return to the

previous mode.

● Adjusting the balance

2-1. Select “Balance”.

3-1. Press the [ENTER] button.

3-2. Turn the [UP/DOWN] knob to adjust the

balance of the right and left speakers.

* The factory default setting is “Center”

(center). (Adjustment range: LEFT 12 to

RIGHT 12 (left 12 to right 12))

3-3. Press the [RETURN] button to return to the

previous mode.

● Adjusting the fader

2-1. Select “Fader”.

3-1. Press the [ENTER] button.

3-2. Turn the [UP/DOWN] knob to adjust the

balance of the rear and front speakers.

* The factory default setting is “Center”

(center). (Adjustment range: REAR12 to

FRONT12 (rear 12 to front 12))

3-3. Press the [RETURN] button to return to the

previous mode.

● Adjusting the non-fader volume

Adjust volume output from the unit’s non-fader

output terminal.

2-1. Select “Non Fader Volume”.

3-1. Press the [ENTER] button.

3-2. Turn the [UP/DOWN] knob to increase or

decrease volume.

* The factory default setting is “0”.

(Adjustment range: -6 to +6)

3-3. Press the [RETURN] button to return to the

previous mode.

● Setting the BBE MP

(Sound Enhancement and Restoration

for compressed audio files)

BBE MP (Minimized Polynomial Non-Linear

Saturation) Process improves digitally

compressed sound, such as MP3, by restoring

and enhancing the harmonics lost through

compression. BBE MP works by regenerating

harmonics from the source material, effectively

recovering warmth, detail and nuance.

* This fuction is effective for the audio files in the

USB mode and the iPod mode (while the iPod

Output Formart is set to “Digital”).

* The factory default setting is “Off”.

2-1. Select “BBE MP”.

To change audio setting

1. Press the [AUDIO] button to switch to the

audio adjustment selection display.

2. Then turn the [UP/DOWN] knob to select

the audio adjustment mode.

Each time you turn the [UP/DOWN] knob,

the sound adjustment mode changes as

following order:

“Bass” ↔ “Treble” ↔ “Balance” ↔

“Fader” ↔ “Non Fader Volume” ↔

(“BBE MP”)

* “BBE MP” can be selected only in the USB/

iPod mode.

3. Press the [ENTER] button.

4. Turn the [UP/DOWN] knob to adjust the

selected audio mode.

5. After completing settings, press the

[RETURN] button to return to the previous

mode.

280PE3260E_EN.book Page 33 Tuesday, March 24, 2009 3:41 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Clarion CMV1 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Clarion CMV1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info