Bedienungsanleitung Clarion CZ209EG (Seite 8 von 23) (Englisch)

580513

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

English

8 CZ209E/CZ209ER/CZ209EG

3-4. Press the [ ] button to return to the

previous mode.

When set to “CUSTOM”:

3-2. Press and hold the [ ] button (1 sec.).

Bass/treble characteristics become flat and

“FLAT” is show in the display.

3-3. Turn the [ROTARY] knob to change to the

“OFF” mode.

● Adjusting the bass

This adjustment is supported only when

Z-Enhancer Plus is set to “CUSTOM”.

2-1. Select “BASS”.

3-1. Press the [ ] button.

3-2. Press [x] or [v] to change and select

settings as follows:

“B<G 0>” ↔ “B<F 60>” ↔ “Q 1”

3-3. Turn the [ROTARY] knob to adjust values

for gain, F (center frequency) and Q curve.

B<G 0> :The factory default setting is “0”.

(Adjustment range:

+7 to –7)

B<F 60> :The factory default setting is

“60”.

(Adjustment range:

60/80/100/200)

Q 1 :The factory default setting is “1”.

(Adjustment range: 1/1.25/1.5/2)

3-4. Press the [ ] button to return to the

previous mode.

● Adjusting the treble

This adjustment is supported only when

Z-Enhancer Plus is set to “CUSTOM”.

2-1. Select “TREBLE”.

3-1. Press the [ ] button.

3-2. Press [x] or [v] to change and select

settings as follows:

“T<G 0>” ↔ “T<F 10K>”

3-3. Turn the [ROTARY] knob to adjust values

for gain and F (center frequency).

T<G 0> : The factory default setting is “0”.

(Adjustment range: +7 to

–7)

T<F 10K>: The factory default setting is

“10K”.

(Adjustment range: 10K/12.5K/

15K/17.5K)

3-4. Press the [ ] button to return to the

previous mode.

● Adjusting the balance

2-1. Select “BALANCE”.

3-1. Turn the [ROTARY] knob to adjust balance

between right and left speakers.

∗ The factory default setting is “CENTER”.

(Adjustment range: RIGHT12 to LEFT12)

● Adjusting the fader

2-1. Select “FADER”.

3-1. Turn the [ROTARY] knob to adjust balance

between front and rear speakers.

∗ The factory default setting is “CENTER”.

(Adjustment range: FRONT12 to REAR12)

● Adjusting the non-fader volume

Adjust volume output from the unit’s non-fader

output terminal.

2-1. Select “NF VOL”.

3-1. Turn the [ROTARY] knob clockwise to

increase volume; turn counterclockwise to

decrease volume.

∗ The factory default setting is “0”.

(Adjustment range: +6 to –6)

Note:

• When in the sound adjustment mode, if no

operation is performed for 10 seconds or more,

the mode is cancelled and the unit returns to the

previous mode.

Setting the MAGNA BASS EXTEND

The MAGNA BASS EXTEND function does not

adjust low frequencies like normal sound

adjustments, but emphasizes the deep bass

range with dynamic sound.

∗ The factory default setting is “OFF”.

1. Press and hold the [SOUND] button (1 sec.)

to enable MAGNA BASS EXTEND.

2. Press and hold the [SOUND] button (1 sec.)

to disable MAGNA BASS EXTEND.

CT (Clock Time) function

The CT function receives CT data sent from an

RDS station and displays the time.

∗ If a CT data is not being received, “CT– –:– –”

appears in the display.

Note:

• CT data is not transmitted in some countries and

by some broadcast stations. Also, in some areas,

the CT may not display accurately.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Clarion CZ209EG Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Clarion CZ209EG

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info