Bedienungsanleitung Clarion CZ209EG (Seite 9 von 23) (Englisch)

580513

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

English

9 CZ209E/CZ209ER/CZ209EG

Radio Operations

Listening to broadcasts

1. Press the [SRC] button and select radio

mode.

∗ PS: Programme service name

∗ PTY: Programme type

2. Press the [BND] button and select the

reception band. Each time the button is

pressed, the band changes as follows:

F1 (FM1) ➜ F2 (FM2) ➜ F3 (FM3) ➜ AM

(MW/LW) ➜ F1 (FM1)...

Tuning

3 tuning modes are available: seek tuning,

manual tuning and preset tuning.

Seek tuning

2 seek tuning modes are available: DX SEEK

and LOCAL SEEK.

DX SEEK can automatically tune to receivable

broadcast stations; LOCAL SEEK can tune to

only broadcast stations with a good reception

sensitivity.

∗ If “MANU” is appeared in the display, press

[BND] (1 sec.).

“MANU” in the display goes off and seek tuning is

now available.

∗ If “TA” is appeared in the display, TP stations are

automatically sought.

● DX SEEK

Press [x] or [v] to automatically seek

stations.

When the [v] button is pressed, the station is

sought in the direction of higher frequencies; if

the [x] button is pressed, the station is sought

in the direction of lower frequencies.

● LOCAL SEEK

If [x] or [v] is pressed and held in position

(1 sec.), local seek tuning will be enabled.

Broadcast stations with good reception

sensitivity are selected.

Manual tuning

2 modes are available: Quick tuning and step

tuning.

● Quick tuning

Press and hold [x] or [v] (1 sec.) to tune a

station.

● Step tuning

Press [x] or [v] to manually tune a station.

∗ If no operation is performed for 7 seconds or

more, manual tuning is cancelled and the display

returns to the previous mode.

Recalling a preset station

A total of 24 preset positions (6-FM1, 6-FM2, 6-

FM3, 6-AM) can be used to store broadcast

stations in memory. Press the corresponding

[DIRECT] button to automatically recall the

stored frequency.

Manual memory

1. Use seek tuning or manual tuning to select

the desired station.

2. Press and hold one of the [DIRECT] buttons

(2 sec.) to store the current station in preset

memory.

Auto store

The auto store function stores up to 6 stations

automatically tuned in sequential order. If 6

stations cannot be found, any previously stored

station remains in its memory position.

1. Press the [BND] button and select the

desired band (FM/AM (MW/LW)).

2. Press and hold the [ ] button (2 sec.). The

stations with good reception are stored

automatically to the preset channels.

∗ If auto store is performed in the FM bands, the

stations are stored in FM3 even if FM1 or FM2

was chosen for storing stations.

Preset scan

Preset scan sequentially receives stations

stored in preset memory. This function is useful

when searching for a station stored in the

memory.

1. Press the [ ] button.

2. When the desired station is received, press

the [ ] button again to continue receiving

that station.

Note:

• Do not press and hold the [ ] button (2 sec.),

or the auto store function will begin and the unit

will begin storing stations.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Clarion CZ209EG Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Clarion CZ209EG

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info