Bedienungsanleitung Clatronic bs 1257 (Seite 34 von 54) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Norwegisch)

316204

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

ENGLISH

Illustration D

(see illustration D)

• Open the clip on the lid (b)

in order to release it from the

dust container (a).

• Turn the ﬁ lter insert (c) a

small amount in an anticlo-

ckwise direction to release it

from the lid (b).

Illustration E

Motor protection ﬁ lter (d)

• The motor protection ﬁ lter is

located in the dust space.

• The ﬁ lter ﬁ ts vertically into the

rear section of the dust hou-

sing. Pull the ﬁ lter upwards to

remove it (see illustration E).

Cleaning the Dust Container and Filter Inserts

• Always empty the dust

container ﬁ rst.

• After use you can rinse out

the dust container with clean

water.

• Any soiling in the container

can be removed with a

sponge or nylon brush.

Filter Insert, Motor protection ﬁ lter

• Quick clean: Tap or brush the ﬁ lters out in order to remove

any residues. The quick clean is recommended every time

the dust container is emptied.

• Hand wash: In the case of more intense soiling we recom-

mend a hand wash up to 40°C.

CAUTION:

You should always carry out this cleaning process if the

suction power of the device is reduced!

ޥ NOTE:

• Simply allow the ﬁ lters to dry in the air!

• The device should only be used again when the ﬁ lters are

dry!

Outlet ﬁ lter (13)

The appliance is also equipped with an outlet ﬁ lter.

• In order to ensure that the ﬁ lter works correctly, we recom-

mend that you replace it every six months.

• This ﬁ lter is to be found on the top side of your device under

a ventilation grille.

• Pull on the button to open the grille.

• Remove the grille by pulling upwards.

• Take out the ﬁ lter and clean it as described above.

• Place the ﬁ lter back in position.

Cleaning and storage

Cleaning

• Pull the plug out of the socket before cleaning!

• Clean the casing with a dry cloth.

Storage

• Let the iron cool down completely.

• Wind the cable completely.

• Insert the hook of the nozzle on the back of the device into

the parking aid (8).

Troubleshooting

• The Device Does Not Work.

Remedy:

Check the connection to the mains.

Check the position of the switch.

• The device does not suck up anything.

Possible Cause:

The suction power is set too low.

Remedy:

Check the position of the control switch.

Possible Cause:

The dust bag is full.

Remedy:

Renew the dust bag.

Possible Cause:

The dust container or the ﬁ lters are dirty.

Remedy:

Empty or clean the components.

Possible Cause:

There is a foreign body in the suction tube or the nozzle.

Remedy:

Check the accessories for foreign bodies.

ޥ NOTE:

Important note!

• Cleaning may become necessary after a shorter time,

depending on the conditions of use, e.g. when vacuuming

ﬁ ne dust.

• If the suction power of your vacuum cleaner diminishes

please clean the ﬁ lters as described.

• If the suction power suddenly diminishes during operation

this may be due to the ﬁ lters being locked.

05-BS 1257 34 04.05.2007, 12:38:04 Uhr

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Clatronic bs 1257 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info