Bedienungsanleitung Clatronic bs 1260 (Seite 40 von 66) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Norwegisch)

319584

Zoom out

Zoom in

Vorherige Seite

1/66

Nächste Seite

ENGLISH

Blower Aperture

• The device has a blower

function. This enables you to

blow out dust or leaves.

• Attach the hose connection

(8) to the blower aperture

(12).

Mains Lead

• To use the device please unwind the entire lead.

• After use you can wind up the lead in the cable duct on the

motor housing.

Parking Position

• On the motor housing your

device has a holder for the

ﬂ oor nozzle.

• Here you can hang up the

nozzle in order to “park” it.

Operation

General

• Select the desired accessory.

• Unwind the lead completely.

• Insert the mains plug into a correctly installed 230V, 50Hz

power socket.

Dry Vacuuming

• Insert the permanent dust bag; it may be necessary before-

hand to remove the hose connection.

• Attach the motor housing.

• Assemble the accessory.

• Turn the device on.

• Vacuum at a steady speed. There is no need to exert

pressure.

Removing and Emptying the Dust Bag

• Turn the device off with the on/off switch (2). Pull the plug

out of the socket.

• Remove the motor housing.

• Take off the hose connection.

• Remove the dust bag.

• Empty the dust bag by pulling off the clip.

• Push the clip back in place and reinsert the bag. Check that

it is inserted properly in the holder.

• Reassemble the hose connection and the motor housing.

• Now you can use the device again.

Wet Vacuuming

CAUTION:

• Never use the dust bag when vacuuming up liquids.

Allow the hose connection to discharge directly into the

collection vessel.

• Do not use the ﬂ oor nozzle, but the parquet brush.

• Before the cleaner is used again for dry vacuuming, all

components must be dry.

• Remove the permanent dust bag and reattach the motor

housing.

• Assemble the attachment.

• Switch the device on.

CAUTION:

Turn the device off immediately if foam forms, liquid leaks out

or if the vessel is full.

ޥ NOTE:

When the vessel is full the ﬂ oat valve (16) closes the suction

aperture and the motor runs at a higher speed. Switch the

device off immediately and empty it.

Emptying the Collection Vessel

• Turn the device off by the on/off switch (2). Pull the plug out

of the socket.

• Remove the motor housing.

• Empty the collection vessel.

• Reassemble the hose connection and the motor housing.

• You can now use the vacuum cleaner again.

Cleaning and storage

• Pull the plug out of the socket.

• In order not to damage the surfaces, please do not use any

abrasive detergents or scratching cleaning utensils.

Collection Vessel

• Rinse out the collection vessel after use with clean water.

• Any dirt in the vessel can be removed with a sponge or

nylon brush.

Permanent Dust Bag

• Quick cleaning: Tap or brush out the dust bag in order to

remove any residues.

• Hand wash: If soiling is more severe we recommend a

hand wash up to 40°C.

ޥ NOTE:

• The bag should only be allowed to dry in the air!

• Only use the vacuum cleaner again when the dust bag is

dry!

05-BS 1260 40 19.09.2006, 12:54:59 Uhr

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Clatronic bs 1260 Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info