Bedienungsanleitung Climastar Silicium Touch (Seite 7 von 12) (Englisch)

773865

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

3.4 AUTOMATIC MODE (continued)

How to select and carry out custom programming.

a) Press the 'OK/mode' button.

b) Select the auto mode by pressing the button until (Automatic Mode) is displayed and press the

'OK/mode' button to confirm.

c) The display will now show the set temperature together with a red dot that indicates the unit is working in

automatic mode. If the unit has been programmed previously then it may show

d) Press the 'OK/mode' button for a few seconds until (Configure Time) is displayed.

e) Press the button and then press the 'OK/mode' button on (Select Day).

f) Press and buttons to select the day you wish to change the on/off times and then press the 'OK/mode'

button.

g) The display now shows or or depending on how it was previously programmed.

The indicates the time in hours, i.e. =12:00am, =01:00am and so on.

h) By using the and buttons you can select (OFF), (ECO) or (ON) for that time period.

Once selected Press the 'OK/mode' button to move onto the next time period.

i) Repeat step h) until you go through all the 24 hours. The display will now show allowing

you to select the next day to program. Press the 'OK/mode' button and continue from step f) if you wish to

program each day individually. Alternatively you can copy one day to the next by following steps in section

3.5 COPY FUNCTION step b).

3.5 COPY FUNCTION

This function enables you to copy a previously programmed day to any other day. i.e. day1 to day2 or day1 to

day5, etc.

To copy the setting of one day into another, do as follows:

a) Press the 'OK/mode' button for a few seconds until (Configure Time) is displayed.

b) Press button until is displayed and press the 'OK/mode' button.

c) Press button to select the day you wish to copy and press the 'OK/mode' button.

d) The display will now show , , etc depending on which day you selected. The first number is

the day you are copying from, the second number is the day you are copying too.

e) By Pressing button you can now change the day you want to copy too, once happy Press the 'OK/mode'

button to copy.

f) You are now taken back to menu where you can Press the 'OK/mode' button to copy

another day (repeat from step c) ) or exit by Pressing the ' /esc' button.

Note:- If (Automatic Mode) is selected the heater cannot be turned off. To turn off the device, Press the

'OK/mode' button and use and buttons to select (Manual Mode) then Press the 'OK/mode' button.

You can now turn off the device using the ' /esc' button.

3.6 PILOT WIRING MODE

In this mode the device works following instructions from an external controller.

How to select FP mode?

a) Press the 'OK/mode' button.

b) Press the button until is displayed and press the 'OK/mode' button.

c) The display will show the set temperature together with a red flashing dot that indicates the unit is working

in FP mode.

Note:- If F.P. mode is selected the heater cannot be turned off. To turn off the device, press 'OK' and using the

and buttons select (Manual Mode) then Press the 'OK/mode' button. You can now turn off the

device using the ' /esc' button.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Climastar Silicium Touch Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info