Bedienungsanleitung Concept VR2020 (Seite 40 von 95) (Deutsch, Englisch, Französisch, Italienisch, Spanisch, Polnisch)

802873

Zoom out

Zoom in

Vorherige Seite

1/95

Nächste Seite

78 79

ENEN

VR2020 VR2020

1 Filter strainer cover

2 Dust container button

3 Wall sensor

Docking station

1 Power indicator light

2 Signal transmission area

3 Base charging contacts

4 Catch groove

5 Cover plate

6 Cable passage

7 AC adapter socket

8 Winding pin

List of parts

1 Docking station 1x

2 Remote control 1x

3 Wiping cloth 2x

4 HEPA ﬁlter + foam ﬁlter 1x

5 Magnetic strip 1x

6 Adapter 1x

7 Cleaning brush 1x

8 Left and right brush 2x

9 Middle rotary “V” brush

10 Hanging water tank 1x

11 Main brush cover with steel wire 1x

3 5

KEY FEATURES

Cleaning / ON/OFF

• Press brieﬂy to start or pause cleaning.

• Press and hold for 3 seconds to switch the appliance

on or oﬀ.

• Long press for 15 seconds to force the appliance to

shut down under unusual circumstances.

Charging / Local cleaning

• Press brieﬂy to start or pause charging.

• Long press to start local cleaning.

Indicator light

• Turquoise: Normal operation or charging.

• Red: Abnormal condition or low battery.

• Light blue: The appliance is not connected to the

network.

Wi-Fi reset

• Press both buttons simultaneously for 3 seconds.

INSTALLATION

1. Connect the power cord and store the excess

cable length in the cable compartment.

2. Place the docking station against the wall and

connect the power.

Note:

• Provide a space of min. 0.5 m on both sides of the

docking station and min. 1.5 m in front of the station.

• If the power cord is stretched vertically to the ground,

the appliance may pull it out and the docking station

may be switched oﬀ.

• In normal condition, the charging indicator light is on

when switched on, and oﬀ when charged.

3. Do not move the docking station or expose it to

direct sunlight.

Note: Direct sunlight will interfere with the docking

station signal and the appliance may not return to the

docking station properly.

4. Installing the side brush

Make sure the left side brush (L) and right side brush

(R) markings correspond to the L and R markings on

the bottom cover. Push the side brushes L and R until

you hear a “click” sound.

5. Putting the appliance into operation and charging

To switch the robot on, press and hold the button .

If the power indicator light is normally on, charge the

robot in the docking station.

Note: If the appliance does not start due to a low

battery, charge it in the docking station and it will start

automatically. Normally, the appliance can only operate

when the battery level is ≥20 %.

6. Connecting a mobile app (you can skip this step)

Read the instructions for connecting Wi-Fi and connect

the mobile app.

7. Start of cleaning

After switching on the robot, brieﬂy press the button

on the robot or start cleaning using the mobile app

(you can pause the appliance by pressing any button

during use).

Note:

• The sweeping robot cannot be used to remove ﬂuids.

• If the battery charge level is less than 20 %, the

appliance cannot operate. In this case, recharge it.

• If the battery charge level is less than 20 %, the

appliance automatically returns to the docking

station.

• Before use, remove various wires (including the

docking station power cord) from the ﬂoor to prevent

outages and damage to objects or wires when the

appliance catches these wires.

8. Installing the wiping module

a) Installing the wiping cloth: glue the wiping cloth

straight to the bottom of the water tank.

Note: Clean the wiping cloth after use to keep it in good

condition.

b) Fill the water tank: open the cover and ﬁll the tank

with water.

c) Install the module:

Push the module horizontally along the back of the

robot. The module is installed in place when you

hear a “click” sound.

9. Removing the wiping module

Once the robot has completed its work, press the

latches on both sides, remove the wiping module

backwards, empty the water from the water tank and

clean the cloth (do not move or ﬂip the robot during

cleaning).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Concept VR2020 Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info