Bedienungsanleitung Concept VR2020 (Seite 41 von 95) (Deutsch, Englisch, Französisch, Italienisch, Spanisch, Polnisch)

802873

Zoom out

Zoom in

Vorherige Seite

1/95

Nächste Seite

80 81

ENEN

VR2020 VR2020

10. Instructions for using the wiping module

• Do not use the wiping module unless supervised.

• For safety, make sure the wiping module is removed

when charging or when not in use.

• Do not attempt to wipe the carpet.

• For a better wiping eﬀect, the wiping module should

be used after sweeping or vacuuming the ﬂoor three

times.

• To reﬁll water or clean the cloth while the appliance

is operating, pause it, remove and reinsert the wiping

module as described in steps 8 and 9. Do not move

or ﬂip the appliance to avoid positioning errors and

map loss.

• The wiping function of the appliance is designed for

wiping and aids deep cleaning. However, it cannot

eﬀectively remove stubborn dirt and thus replace

human power.

USE

ON/OFF

Press and hold the button for 3 seconds, the indicator

light comes on and the appliance starts.

Press and hold the button for 3 seconds while the

appliance is in standby mode, the indicator light goes out

and the appliance switches oﬀ.

NOTE: The appliance cannot be switched oﬀ while it is

being charged.

CLEANING/PAUSE

After starting the appliance, brieﬂy press the button on

the appliance or start the appliance using the mobile app

(press any button to pause the appliance).

Note:

• The robotic vacuum cleaner cannot be used to

remove ﬂuids.

• If the battery charge level is less than 20 %, the

appliance cannot operate. In this case, recharge it.

• If the battery charge level is less than 20 %, the

appliance automatically returns to the docking

station.

• Before use, remove various wires (including the

docking station power cord) from the ﬂoor to prevent

outages and damage to objects or wires when the

robot catches these wires.

CHARGING

Automatic mode: The appliance automatically returns to

the docking station after work.

Manual mode: When paused, press the button brieﬂy

to start charging or you can use your mobile app to

charge the appliance. The indicator light ﬂashes when the

appliance is fully charged.

Note: If the appliance does not ﬁnd the docking station,

it will automatically return to its original position. In this

case, place the device manually into the docking station.

MAGNETIC STRIP

Magnetic strips can be set to separate areas that should

not be cleaned (for example, bathrooms, kitchens, etc.).

Note: attach the magnetic strip to the ﬂoor so that it

cannot move. Otherwise, it will aﬀect its eﬀectiveness.

CLEANING MODE

Upon start-up, the appliance will move according to the

cleaning program in curves to clean up the entire ﬂoor

area and complete the cleaning of all rooms one by one

in a regular, eﬃcient manner with full coverage. When

cleaning is complete, the appliance returns to the docking

station and recharges automatically.

LOCAL CLEANING

By pressing and holding the button for 3 seconds, the

robot is localized, cleans a circular area of 1.5 m diameter,

and automatically stops when cleaning is complete.

CLEANING PLANNING

You can set a ﬁxed cleaning time using the mobile app.

The appliance will automatically start cleaning at the

speciﬁed time and will return to the docking station when

completed.

WI-FI RESET

If the mobile phone cannot connect to the appliance

due to a change in router and password conﬁguration

or other reasons, press the button and the button

for 3 seconds at the same time until you hear the “Wi-Fi

has been reset” voice prompt and until the indicator light

turns on light blue and ﬂashes slowly.

SILENT MODE

You can turn robot voice messages on or oﬀ using the

mobile app.

SETTING THE SUCTION POWER

You can set the suction power to a quiet, standard or high

level using the mobile app.

When the carpet is detected, the suction force

automatically increases to the highest level.

UV LAMP AND STERILIZATION

You can turn the UV lamp on/oﬀ using the app or the

remote control. For safety reasons, do not turn it on with

the wiping module attached.

The UV lamp can be turned on during complete cleaning,

peripheral cleaning or local TURBO cleaning.

Note:

• The UV lamp cannot be used during charging, standby

mode, low battery capacity, pause, etc.

SCENTED TABLET

On the bottom side of the HEPA ﬁlter cover on the dust

container, there is the chamber for the scented tablet. Put

the scented tablet into the chamber and press the lock to

close it.

USING THE REMOTE CONTROL

1. Cleaning planning

2. Moving forward

3. Turning left

4. UVC light

5. Start/pause charging

6. Timer

7. Automatic cleaning/pause

8. Turning right

9. Peripheral cleaning

10. Setting suction power

Note: To ensure that all the correct settings are eﬀective,

you must point the remote control at the front of the

robotic vacuum cleaner from close proximity.

Time setting

1. Press the button on the remote control to enter

the time setting, the Sunday symbol ﬂashes on the

LCD.

2. Press the left and right buttons to select the day of the

week and press the button to conﬁrm it, then the

LCD will automatically switch to the clock setting.

3. Press the up and down buttons to set the hour and

press the left and right buttons to move to the minute

setting.

4. After setting the current time, point the remote control

at the front of the robotic vacuum cleaner and press

the button to conﬁrm all time settings. Failure to

do so will invalidate your settings.

5. This completes the time setting for both the remote

control and the robotic vacuum cleaner.

Cleaning plan

1. Press the button on the remote control to enter

the plan setting function, the Sunday symbol ﬂashes

on the LCD.

2. Press the left and right buttons to select the day of the

week and press the button to conﬁrm it, then the

LCD will automatically switch to the clock setting.

3. Press the up and down buttons to set the hour and

press the left and right buttons to move to the minute

setting. Then point the remote control at the front of

the robot vacuum cleaner and press the button

to conﬁrm this plan setting for the robotic vacuum

cleaner.

4. When one plan setting is completed, the remote

control automatically moves to the next plan setting.

If you do not want to continue with the setting, press

the exit button or wait 10 seconds for the setting

Concept VR2020 Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info