Bedienungsanleitung Condair RS (Seite 14 von 80) (Englisch)

652338

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

14 Operation

4.3 Commissioning after an interruption of operation

The following description outlines the start up procedure after an interruption of operation (e.g. after ser-

vicing the steam humidier). It is assumed that rst-time commissioning has been carried out properly by

the service technician of your Condair representative and the Condair has been congured accordingly.

1. When putting the steam humidier into operation the rst time or when putting the steam humidier

into operation after work has been carried out on the steam system, the operating personnel must

check whether the steam pipe is open over the entire length. To do this proceed as follows:

Remove the front door on the steam cylinder side of the Condair RS.

• Undo the upper hose clamp of the steam hose in the unit with a screwdriver and pull the hose

down to remove it from the steam connection.

• Start up the ventilation system and check whether the pressure on the open steam connector

corresponds to the pressure in the ventilation system.

DANGER!

A steam line that is reduced in cross section or completely closed will cause an excessive

increase in pressure in the steam cylinder when the unit is operating and could lead to the

risk of scalding accidents!

Therefore: If no draught or only a slight one can be detected the steam line must be checked for

blockages and reductions in cross section before continuing with commissioning and you must

ensure that the steam line is open across the entire length and through the whole cross section.

2. Examine the steam humidier and installation for possible damage.

DANGER!

A damaged unit or systems with damaged installations may present danger to human life

or cause severe damage to material assets.

Therefore: Damaged systems and/or systems with damaged or faulty installations must not be

operated.

3. Mount front doors of the unit and lock it (if applicable).

4. Open the lter valve / shut-off valve in the water supply line.

5. Switch on the electrical isolators in the mains supplies (heating and control voltage).

6. Switch on the unit switch of the steam humidier.

The steam humidier carries out an automatic system test (initialising). If a fault is detected during

the system test, a corresponding fault message is shown in the maintenance and malfunction indi-

cation eld (see chapter 5.1.2).

Iftheinitializationissuccessful, the steam cylinder lls up and a function check on the level unit

is carried out. If a fault is detected during the function check on the level unit, a corresponding fault

message is shown in the maintenance and malfunction indication eld (see chapter 5.1.2).

If the function check on the level unit is successful, the Condair RS will be in normal operating

mode and the standard operating display is shown. The heating current switches on as soon as

the humidity controller/humidistat demands humidity. The LED lights green and steam is produced

after a short delay.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Condair RS Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Condair RS

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info