Bedienungsanleitung Condair RS (Seite 68 von 80) (Englisch)

652338

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

68 Maintenance

6.8 Performingsoftwareandrmwareupdates

To update the control software or the driver board rmware, proceed as follows:

1. Set the On/Off switch on the front side of the steam humidier to the Off position, then switch off the

voltage supply to the steam humidier via the external disconnect switch (electrical isolator) and

secure switch in the off position to prevent it from inadvertent power up.

2. Unlock the door panel on the control compartment side of the steam humidier and remove it.

3. Swing control panel assembly open.

4. Carefully insert FAT32 formatted USB memory stick containing the software updates into the USB

port on the control board. Make sure that the maximum length of the memory stick does exceed 75

mm.

Note: in order to update the control software or the rmware of the driver board a USB stick with a

valid software update (the update les must be on the highest level outside of any folder) must be

connected to the USB port on the control board. Otherwise, an appropriate fault message appears

when starting the software update.

5. Close control panel assembly, then close the door panel of the control compartment and lock it with

the screw.

6. Remove the lock and tag from the external disconnect switch. Then, switch on external disconnect

switch to restore power to the humidier.

7. Set the On/Off switch on the front side of the steam humidier to the On position.

8. When the standard operating display appears, select the <Menu> button, then enter the password

(8808) to login.

9. Select "Administrator > Software Update tab", then select the desired update function:

• select "Software Update" to update the control software,

• select "Driver A.DB.A" update the rmware for the driver board of Module A

• select "Driver B.DB.B" update the rmware for the driver board of Module B (on double unit or

large units with two steam cylinders),

• select "Driver C.DB.A" update the rmware for the driver board of optional Condair RO-A reverse

osmosis system (only possible, if Condair RS is congured for the operation with a Condair RO-A

reverse osmosis system).

The update starts. A progress bar is shown in the display. If the update has completed the control

unit returns to the standard operating display.

CAUTION!

Do not interrupt a software or rmware update once it has started. Wait until updating is completed.

Corrupted control software or rmware can render the humidier unusable.

Note: If software update is accidentally interrupted, the humidier will not operate, but the software

update can be resumed by leaving the USB key inserted in the control board and power cycling

the unit. The integrated controller will detect the software was not properly installed, and restart

the update.

10. Repeat steps 1 to 3, then carefully remove the USB memory stick.

11. Close control panel assembly, then close the door panel of the control compartment and lock it with

the screw.

12. Repeat Step 6 and 7 to power up the humidier.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Condair RS Seite 68

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Condair RS

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info