652338
70
Zoom out
Zoom in
Vorherige Seite
1/80
Nächste Seite
70 Fault elimination
Fault
Operational states where further operation is not possible, or where further
operation would damage the system are indicated with a fault message, ad-
ditionally the fault indicator LED below the touch panel will lights up red. If
such a malfunction occurs, the steam production of the Condair RS will be
stopped automatically.
By pressing on the maintenance and malfunction indication eld in the standard operating display the
error list shown with all active warning and fault messages. By pressing on the corresponding Warning or
Fault entry additional information regarding the malfunction are displayed (see display on the far-right).
7.3 Malfunction list
Most operational malfunctions are not caused by faulty equipment but rather by improper installation or
disregarding of planning guidelines. Therefore, a complete fault diagnosis always involves a thorough
examination of the entire system (e.g. hose connections, humidity control system, etc.).
Code Message Information
Warning Fault Possible causes Remedy
W02 ––– BMS Timeout BMS (Modbus, BACnet, LonWorks) has stopped sending humidity/demand
updates.
Signal cable from BMS not connected
correctly or defective.
Correctly connect or replace signal
cable.
Interfering signal present. Eliminate source of interfering signal.
Address conict with other units in the
chain.
Correctly set unit addresses.
W20 E20 Safety Loop External safety chain is open, humidication is stopped!
Note: as soon as the safety chain is closed again the humidication system
Condair RS continues to work normally.
Ventilation interlock open. Check/switch on fan of the AHU.
Air proving switch has triggered. Check fan/lter of the AHU.
High limit humidistat has triggered. Wait, check/replace high limit humi-
distat.
Fuse "F2" on the driver board defec-
tive.
Replace fuse "F2" on the driver board.
70

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Condair RS wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Condair RS

Condair RS Installationsanweisung - Englisch - 80 seiten

Condair RS Bedienungsanleitung - Holländisch - 80 seiten

Condair RS Installationsanweisung - Holländisch - 76 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info