Bedienungsanleitung Consolar Control 601 (Seite 7 von 63) (Englisch)

743662

Zoom out

Zoom in

Vorherige Seite

1/63

Nächste Seite

TDMA CONTROL 601/701:

Published 07/2007

System variation 1

Return flow tempe-

rature raising

No function, Solid

fuel boiler,

T-Pro

Return flow sensor

No winter switch

over

System variation 2, 3

Heating regulation

Inflow sensor

CONTROL 701

Regulator Setting

Sensor

System variation

1,2,3

Heating regulation

Inflow sensor

Solar Difference:

2...12 K

The temperature difference by which the collector sensor

temperature must be higher than the lower thermal store

temperature to enable solar loading of the thermal store is

set using the „Solar Difference“ function. A lower value

can be set if the pipe diameters are small and the insula-

tion is good. Long pipe runs, larger diameter pipework,

poor insulation or unfavourable sensor positioning require

a higher temperature difference.

Example:

With 15 mm diameter pipes, 20 m pipe run, an electri-

cally economic pump and good pipe insulation a value

of 6K can be set. Using a setting of 6K the solar pump

will switch on when the collector sensor temperature is at

least 6K higher than the lower thermal store temperature.

When the temperature difference between the collector

and the lower thermal store drops below 4K (hysteresis

of 4K set in the factory) the solar pump will switch off.

Solar pump: Inputs – Function - Output

Input

Function

Collector sensor

(in delivery package)

Top loading (Stratified

loading function)

Solar difference

Maximum solar input

Lower thermal store sensor

(in delivery package)

Solar difference

Maximum solar input

Inflow / Return flow sensor

(Art. N

. RE 046)

Winter switch over

Output: Solar pump

2.3.2 East-West-Valve-Regulation

A system which includes two solar collector array areas,

one oriented east and one oriented west, can be regulated

using the „East-West- Valve“ function.

Solar Difference 2:

2...12 K

The „Solar Difference 2“ function is used to set the tem-

perature difference by which the temperature registered at

the sensor on the second collector must be higher than the

temperaure at the lower thermal store sensor before solar

loading of the thermal store can begin. The „East-West-

Valve“ switches a three way valve to AB-A to divert the

warm water flow to the second collector when the second

collector is 3K warmer than the first collector.

East-West-Valve: Input - Function - Output

Input

Function

Collector sensor 2

(Art. N

. RE 040)

Solar difference 2

Maximum solar input

Output: East-West-Valve

2.3.3 Cooling, Twin Thermal Store and Swimming Pool

Regulating

It is possible to choose between the following functions us-

ing Optional Function 1: Cooling / Cooling via the heat-

ing circuit / Twin thermal store prioritizing / Twin thermal

store balancing / Swimming pool.

These functions prevent overheating of the collectors or al-

low a second thermal store to be loaded with hot water.

The solar pump continues to run while the thermal store

cools down, as long as the maximum collector or thermal

store temperature is not exceeded.

Cooling Optional Function:

If the upper thermal store temperature reaches the preset

value „cooling“ is activated. This function can be used for

example to control a thermal store loading pump to cool

the thermal store or to divert the heated water to another

thermal store.

Cooling temperature:

30...90 °C

The required cooling temperature can be set here.

Hysteresis:

2...10 K

The switch hysteresis for cooling can be set here.

For example, if a temperature of 85 °C and a hysteresis of

5 K is chosen, the contact will be closed at 85 °C and re-

opened at 80 °C.

Cooling via Heating Circuit Optional Function:

This function allows the thermal store to be cooled via a

heating circuit when it reaches a set temperature. The

mixer and the heating circuit pump will operate automati-

cally.

Setting the cooling temperature and hysteresis are de-

scribed under „Cooling Optional Function“.

Heating Circuit Inflow Temp: Target:

30...90 °C

The required heating circuit target inflow temperature can

be set here.

Optional Function Twin Thermal Store Prioritizing: When

the upper thermal store sensor reaches the preset tempera-

ture the „twin thermal store“ function is activated. This acti-

vates a three way valve so that the heat flow is diverted to

another thermal store, and simultaneously switches from

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Consolar Control 601 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info