Bedienungsanleitung Constructa CA425252 (Seite 44 von 64) (Deutsch, Englisch, Holländisch, Französisch)

542399

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Fixing malfunctions

Malfunctions are usually due to small details. Before calling the

Technical Assistance Service you should bear in mind the

following advice and warnings.

Normal noise while the appliance is working

Induction heating technology is based on the creation of

electromagnetic fields that generate heat directly at the base of

the pan. Depending on how the pan has been manufactured,

certain noises or vibrations may be produced such as those

described below:

A deep humming sound as in a transformer

This noise is produced when cooking with a high power level. It

is caused by the amount of energy transferred from the hob to

the pan. The noise disappears or becomes faint when the

power level is lowered.

A low whistling sound

This noise is produced when the pan is empty. The noise

disappears when water or food is added to the pan.

A crackling sound

This noise occurs in pans which are made from different

materials superimposed on one another. It is caused by the

vibrations that occur in the adjoining surfaces of the different

superimposed materials. The noise comes from the pan. The

amount of food and cooking method can vary noise intensity.

A high-pitched whistling sound

This noise is produced mainly in pans made from different

materials superimposed on one another, and it occurs when

such pans are heated at maximum power on two hotplates at

the same time. The whistling disappears or becomes fainter as

soon as the power level is lowered.

Noise from the fan

For proper use of the electronic system, the temperature of the

hob must be controlled. To do this, the hob has a fan which

turns on when a high temperature is detected. The fan may also

work by inertia after the hob has been switched off, if the

temperature detected is still too high.

The noises described are normal, they are part of induction

heating technology and not a sign of malfunction.

Indicator Malfunction Solution

none The electric power supply has been cut off. Use other electrical appliances to check whether there

has been a power cut.

The appliance has not been correctly con-

nected following the connection diagram.

Check that the appliance has been connected cor-

rectly according to the connection diagram.

Electronic system malfunction. If none of the above checks resolve the malfunction,

contact the Technical Assistance Service.

The indicators flash The control panel is damp or an object is rest-

ing on it.

Dry the control panel area or remove the object.

The indicator - flashes on

the hotplate indicators

A fault has occurred in the electronic system. Briefly cover the control panel with your hand to con-

firm the malfunction.

“§ + number / š + number

/ ¡ + number

Electronic system malfunction. Unplug the hob from the mains. Wait about

30 seconds before plugging it in again.*

”‹ / ”Š There is an internal operating error. Unplug the hob from the mains. Wait about

30 seconds before plugging it in again.*

”ƒ The electronic system has overheated and

the corresponding hotplate has been

switched off.

Wait until the electronic system has cooled down suffi-

ciently. Then press any symbol on the hob. *

”… The electronic system has overheated and all

hotplates have been switched off.

”† + power level and

beep

There is a hot pan on the control panel. It is

highly likely that the electronic system will

overheat.

Remove that pan. The malfunction indicator will switch

off shortly afterwards. You can carry on cooking.

”† and beep There is a hot pan on the control panel. The

hotplate has switched off to protect the elec-

tronic system.

Remove that pan. Wait a few seconds. Press any con-

trol panel. When the malfunction indicator switches off,

you can carry on cooking.

—‚ Incorrect supply voltage, outside normal oper-

ating limits.

Contact your electricity board.

—ƒ / —„ The hotplate has overheated and has

switched off in order to protect its hob.

Wait until the electronic system has cooled down suffi-

ciently before switching it back on.

* If the warning persists call the Technical Assistance Service.

Do not rest hot pans on the control panel.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Constructa CA425252 Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Constructa CA425252

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info