Bedienungsanleitung Cramer 82HD62 (Seite 4 von 135) (Alle Sprachen)

818999

Zoom out

Zoom in

Vorherige Seite

1/135

Nächste Seite

1 DESCRIPTION

1.1 PURPOSE

This machine is intended for cutting and trimming hedges and

bushes in commercial use. It is not intended to be used for

cutting above shoulder level.

1.2 OVERVIEW

Figure 1

1Speed control button

2Trigger

3Rear handle

4Rotating button

5Blade

6Guard

7Front handle

8Activation switch

9power button

10 Anti-jamming button

2 SAFETY

WARNING

Make sure that you do/obey all safety instructions.

Refer to Safety Manual.

3 INSTALLATION

3.1 UNPACK THE MACHINE

WARNING

Make sure that you correctly assemble the machine before

use.

WARNING

• If the parts are damaged, do not use the machine.

• If you do not have all the parts, do not operate the

machine.

• If the parts are damaged or missing, speak to the service

center.

1. Open the package.

2. Read the documentation in the box.

3. Remove all the unassembled parts from the box.

4. Remove the machine from the box.

5. Discard the box and package in compliance with local

regulations.

3.1.1 INSTALL THE BLADE ASSEMBLY

Figure 5.

1. Put the machine on a flat and smooth surface.

2. Slide the blade assembly (15) into the rotating shaft (17).

3. Insert the bolts and tighten with a screwdriver (not

included).

3.1.2 CONNECT THE BATTERY PACK TO

THE MACHINE

Figure 2.

1. Insert the plug (11) of one side of the cable into the

socket (12) in the machine – line up the lugs on the plug

with the slots in the socket.

2. Push the plug into the socket until it stops, then turn it

clockwise until the plug’s latch engages audibly.

3. Insert the plug (13) of the other side of the cable into the

socket (14) in the battery – line up the lugs on the plug

with the slots in the socket.

4. Push the plug into the socket until it stops, then turn it

clockwise until the plug’s latch engages audibly.

4 OPERATION

• Touch the blade carefully.

• Do not put your fingers into the notches or in position

where they can get cut.

• Do not touch the blade unless you remove the battery

pack.

• Do not use the machine if the blade is damaged or bent.

• Remove all objects such as cords, lights, wire, or string

which can become entangled in the cutting blade and

create a risk of personal injury.

WARNING

If the blade jams on an electrical cord or line, DO NOT

TOUCH THE BLADE! IT CAN BE LIVE AND

DANGEROUS. Do the steps below:

1. Hold the insulated rear handle or put the machine down

and away from you.

2. Disconnect the battery from the battery pocket. Then

disconnect the cable before removing it from blade.

5 OPERATION

• Touch the blade carefully.

• Do not put your fingers into the notches or in position

where they can get cut.

• Do not touch the blade unless you remove the battery

pack.

• Do not use the machine if the blade is damaged or bent.

• Remove all objects such as cords, lights, wire, or string

which can become entangled in the cutting blade and

create a risk of personal injury.

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cramer 82HD62 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info