Bedienungsanleitung Cramer 82HD62 (Seite 5 von 135) (Alle Sprachen)

818999

Zoom out

Zoom in

Vorherige Seite

1/135

Nächste Seite

WARNING

If the blade jams on an electrical cord or line, DO NOT

TOUCH THE BLADE! IT CAN BE LIVE AND

DANGEROUS. Do the steps below:

1. Hold the insulated rear handle or put the machine down

and away from you.

2. Disconnect the electrically service to the damaged line

or cord before you try to free the blade.

5.1 START THE MACHINE

Figure 3.

1. Press the power button (9).

2. Push and hold the micro switch (8) with one hand.

3. Push the trigger (4).

5.2 STOP THE MACHINE

Figure 3.

1. Release the trigger to stop the machine.

5.3 4-STEP SPEED ACTIVATION

Figure 3.

1. This machine has 4-step speed limiter. The feature is used

to optimize performance and runtime after the different

circumstances. With a higher cutting speed you consume

more energy opposed to using a lower cutting speed and

saving energy for more run time. To use the 4-step speed

limiter, pull speed control button forward to change the

speed limiter.

5.4 REVERSE ROTATION FUNCTION

1. If the branch is blocked in the blade, push the anti-

jamming button on the control panel, the blade will

reverse and the branch will be released.

5.5 TURN THE REAR HANDLE

Figure 4.

You can use the rotating button to adjust the rear handle to

different positions to cut the hedges easier.

1. Pull the rotating button and turn the rear handle.

2. Release the rotating button until it locks into position.

5.6 OPERATION TIPS

• Do not push the machine through heavy shrubbery. This

can cause the blade blockage. If the blades blocks,

1. stop the machine.

2. remove the battery pack.

3. remove the blockage.

• Do not try to cut too large stems or twigs.

• Wear the gloves when you cut.

• Cut the new growth with a wide sweeping action so that

the stems are put directly into the blade.

• You can use a string to adjust the height of the hedge.

1. Stretch a piece of string along the hedge at this

height.

2. Cut the hedge immediately above this string.

3. Cut the side of a hedge until it will be narrower at the

top. More of the hedge will come into view in that

way.

6 MAINTENANCE

CAUTION

Do not let brake fluids, gasoline, petroleum-based materials

touch the plastic parts. Chemicals can cause damage to the

plastic, and make the plastic unserviceable.

CAUTION

Do not use strong solvents or detergents on the plastic

housing or components.

WARNING

Remove the battery pack from the machine before

maintenance.

6.1 CLEAN THE MACHINE

WARNING

Keep the machine and the motor free of leaves, branches or

excessive oil to prevent fire risks.

• Use a moist cloth with a mild detergent to clean the

machine.

• Clean all moisture with a soft dry cloth.

• Use a small brush to clean the air vents.

6.2 LUBRICATE PLUG

Figure 6.

To increase the efficiency and life of the machine, check and

lubricate the machine monthly.

NOTE

Lack of the lubricate oil will cause the excessive noise,

overheating or damage.

1. Use the screwdriver ( not included ) to remove the

lubricate plug (16).

2. Inject sufficent lubricate oil with the grease gun or tube

(not included) to the lubricate plug.

3. Insert and tighten the lubricate plug.

English EN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cramer 82HD62 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info