Bedienungsanleitung Cramer 82ZT132 (Seite 13 von 201) (Alle Sprachen)

818975

Zoom out

Zoom in

Vorherige Seite

1/201

Nächste Seite

7 MAINTENANCE

Regular maintenance is the best prevention for costly

downtime or expensive, premature repair. The following

pages contain suggested maintenance information and

schedules which the operator should follow on a routine

basis. Remain alert for unusual noises, as they could be

signaling a problem. Visually inspect the machine for any

abnormal wear or damage.

7.1 MOWER BLADE MAINTENANCE

Check the mower blades daily. They are the key to power

efficiency and well-groomed turf. Keep them sharp -- a dull

blade will tear rather than cut the grass, leaving a brown

ragged top on the grass within a few hours. A dull blade also

requires more power. Replace any blade that is bent, cracked

or broken.

WARNING

Never attempt to straighten a bent blade by heating, or weld

a cracked or broken blade as the blade may break and cause

serious injury. Replace worn or damaged blades.

WARNING

Never work with blades while magnetic bar is in the

ignition switch. Remove magnetic bar from switch and

disconnect battery cables by pulling inward on RED battery

quick disconnect handle in battery box compartment. Block

up mower when you must work under it. Wear gloves when

handling blades. Always check for blade damage if mower

strikes a rock, branch or other foreign objects!

DANGER

The blade adapter will come off when the blade cap screw

is removed. Touch-up sharpening can be done with a file.

Check the blades for balance following grinding. A

commercial balancing tool is available through most

hardware supply stores, or balancing can be done by placing

the blade on an inverted line punch or 12.7mm bolt. Blade

should not lean or tilt. While spinning the blade slowly, it

should not wobble. If blade is out of balance, true it up

before reinstalling. Lay the blade on a flat surface and check

for distortion. Replace any distorted blade.

WARNING

• The blade sail (curved part) must be pointing upward

toward the inside of the deck to ensure proper cutting.

• When mounting blades, rotate them after installation to

ensure blade tips do not touch each other or sides of the

mower.

• Failure to correctly torque the bolt may result in the loss

of the blade, which can cause serious injury.

• Mower blades are sharp and can cut. Wear gloves and

use extra caution when servicing them.

7.1.1 REMOVE THE BLADE

See figure 11-12

You can cut the grass in two differnt ways: Side discharge

blade and mulching blade. With the mulching blade, you can

cut the grass more intensively.

1. Remove the magnetic bar and disconnect battery cables

by pulling inward on RED battery quick disconnect

handle in battery box compartment.

2. Lift the front of the mower and block and secure the

machine to allow service man to change the blade under

the mower.

3. While wearing leather padded gloves, grasp the blade

closely with one hand in order to prevent the blade from

turning and use a 24mm wrench with your other hand to

loosen the bolt fixing its blade in place.

4. Turn the bolt COUNTERCLOCKWISE to loosen and

CLOCKWISE to tighten.

5. Remove the bolt, washer and the blade.

NOTE

If you use the mulching blade, it is necessary for you to

install the two mulcher covers, and the side mulcher plate.

Otherwise, only install the side discharge chute.

7.1.2 INSTALL THE BLADE

1. Place the blade with the cutting blade toward the ground.

2. Install the bolt.

3. Turn the blade bolt CLOCKWISE with a socket or

wrench to secure the blade.

4. Thread the blade nut on the shaft and finger tighten.

5. Torque the blade nut down clockwise using a

torquewrench (not provided) to ensure the bolt is

properlytightened. The recommended torque for the blade

nut is 155-160N.m.

7.2 TIRES

It is important for level mowing that all tires have the correct

amount of air pressure. The recommended pressure are:

NOTE

Tire pressure should only be measured or adjusted when

tires are cold.

Drive wheels 20 psi

Front caster wheels 28 psi

NOTE

Inspect the tires daily. Replace immediately if damaged.

English EN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cramer 82ZT132 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info