Bedienungsanleitung Cramer 82ZT132 (Seite 14 von 201) (Alle Sprachen)

818975

Zoom out

Zoom in

Vorherige Seite

1/201

Nächste Seite

WARNING

Check the tire pressure carefully while inflating. Too much

air in the tire could cause the tire to burst, causing serious

personal injury.

7.3 LUBRICATION

NOTE

Replace the gearbox oil after you operate the machine for

50 hours for the first time, then replace the oil every 500

hours.

Brand Gear-

box

Moto

type

Gearbox

ratio

Oil

quantity

Oil brand

82ZT132 SP600 AC 32 0.6L GL-5

85W-140

7.4 TORQUE VALUES

WARNING

Particular attention must be given to tightening the drive

wheel lug nuts and blade spindle bolts. Failure to correctly

torque these items may result in the loss of a wheel or blade,

which can cause serious damage or personal injury.

Torque values are given below:

Part Ft-lbs. Nm

Wheel (lug) nuts 83-118 112-132

Blade spindle bolt 114-118 155-160

Lug nuts only -It is recommended that these be checked after

the first 2 hours of operation, initially, every 100 hours and

following removal for repair or replacement.

7.5 SEAT BELT MAINTENANCE

Inspect the seat belt system (all seat, seat belt parts, seat pan

and seat pan latch) daily prior to mowing for signs of any

damage. These parts should be replaced if any parts indicate

signs of:

• cuts

• fraying

• extreme or unusual wear

• significant discoloration due to UV exposure

• dirt or stiffness

• abrasion to the seat belt webbing

• damage to the buckle, latch plate or hardware

• any other problem

If the seat belt is to be cleaned, use soap and water. Do not

use carbon tetrachloride, naphtha, etc., as these will weaken

the webbing. For the same reason, do not bleach or dye the

webbing. Replace seat belt if worn or damaged.

7.6 ROPS MAINTENANCE

ROPS Inspection

NOTE

Inspect the ROPS after the first 20 hours of operation.

• Check the torque of the ROPS mounting bolts. Tighten

the bolts to the correct torques (M12, 95N.m) if

necessary.

• Inspect the operator’s seat and the mounting parts for the

seat belt. Tighten the bolts to the correct torque as shown

below, if necessary, and replace parts that show wear or

damage.

• Inspect the seat latch to make sure it is secured and

functioning properly. Adjust or repair, as necessary.

Possible damage to the ROPS

If the unit has rolled over or the ROPS has been in some other

type of accident (such as hitting an overhead object during

transport), the ROPS must be replaced to retain the best

protection. Following an accident, check the ROPS, the

operator’s seat, the seat belt, seat belt mountings and seat

latch for possible damage. Before operating the machine,

replace all damaged parts.

NOTE

The ROPS structure’s protective capability may be

impaired by structural damage, overturn or alteration. Do

not remove or alter any of the ROPS parts. Do not attempt

to weld or straighten ROPS. Failure to adhere to these

instructions could result in severe injury or death.

7.7 BATTERY PACK MAINTENANCE

Your Cramer mower is powered by a battery pack which,

when maintained properly, will provide years of useful life.

For proper care, adhere to the following instructions:

• Always charge batteries after each use.

• Whenever a battery pack is fully discharged and turned

off, it is best to recharge the battery as soon as possible.

Over-discharge of the battery pack means the battery life

will be shortened and the battery may become

permanently damaged. There is no need to fully charge; it

will be beneficial even if you only charge the battery pack

for 5-10 minutes. It is best to recharge it within 24 hours.

• Check that battery cables are securely tightened to

batteries each time you service the battery.

• Keep grass, dirt and debris from collecting near battery

terminals and in battery area.

• Charge batteries indoors in a well-ventilated and dry

location away from sparks or flames. Never expose

charger to rain, vapor or liquid.

• Charge only lithium batteries provided by Cramer.

• Do not touch uninsulated portion of charger (terminal

pins) or of output connector.

• Do not use with defective cords and wires. Replace

defective cords and wires immediately.

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cramer 82ZT132 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info