Bedienungsanleitung Crivit 14103504L IAN 276356 (Seite 8 von 37) (Deutsch, Englisch, Holländisch, Dänisch)

736857

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

8 GB/IE/NI

Installation / Start-upSafety / Preparation

To prevent burns, ensure that the light is switched

oﬀ and has cooled down before touching it.

Lamps develop a lot of heat in the area of the

lamp head.

Attention! Do not touch bulb components or

bulbs during operation as they can reach tem-

peratures > 90 °C.

Allow the light to cool down completely before

replacing a defective bulb.

Replace defective bulbs with new ones immedi-

ately. Use only those bulbs as stated in the

chapter on “Technical Data”. Before changing

bulbs, always ﬁrst remove the fuse or switch oﬀ

the circuit breaker.

The LED light bulbs are permanently ﬁtted and

are not replaceable.

Do not look directly into the light source (light

bulb, LED etc.).

The colour LEDs are only suitable as decorative

lighting, as the chromaticity coordinates of the

LEDs are within a range covered by Regulation

(EU) 2015 / 1428, Article 3, Paragraph 2.

The colour LEDs are not intended for any other

applications.

The ﬁxed illuminant (G4 lamp excluded) is not

replaceable; when the illuminant reaches the end

of its useful life, the entire light must be replaced.

The permanently ﬁtted LED light bulbs are not

suitable for dimmer or electronic switches.

Do not look at the LED with an optical instrument

(e.g. magniﬁer).

Safe working

Only use LED lamps with GU10 base and

maximum output of 3 Watt.

Do not touch the halogen lamps with bare hands.

If this accidentally occurs, the light bulb must

be wiped with alcohol and a lint-free cloth.

Mount the light so that it is protected from

moisture and dirt.

Carefully prepare for assembly and allow your-

self adequate time. Organise all parts and any

necessary additional tools or materials before

starting so they are easy to reach.

Always be attentive! Always pay attention to

what you are doing and proceed with caution

at all times. Never install the light if you are hav-

ing diﬃculty concentrating or do not feel well.

Preparation

Required tools and material

The tools and materials speciﬁed are not included.

This information and these values are non-binding

and are only provided as a reference. The nature

of the material is determined by the individual local

conditions.

- Pencil / making tool

- Voltage tester

- Screwdriver

- Electric drill

- Bit (ø 8 mm)

- Side cutting pliers

- Ladder

Prior to installation

Important: The electrical connection must be

established by a trained electrician or a person

trained to perform electrical connections. This per-

son must be familiar with the properties of the light

and the connection regulations.

Familiarise yourself with all the instructions and

diagrams in this manual, as well as with the

light itself, before you install it.

Before installation ensure that the circuit, to

which the light will be connected, is not ener-

gised. To do so, remove the fuse or switch oﬀ

the circuit breaker in the fuse box (0 position).

Use the voltage tester to verify the de-ener-

gised status.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Crivit 14103504L IAN 276356 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Crivit 14103504L IAN 276356

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info