Bedienungsanleitung Crivit 14103504L IAN 276356 (Seite 10 von 37) (Deutsch, Englisch, Holländisch, Dänisch)

736857

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

10 GB/IE/NI

Disposal / Warranty / Service centreStart-up / Cleaning / Disposal

Remote control functions

ON / OFF GU10 LED lamp and colour LEDs

are on / oﬀ

Lamp GU10 lamp on / oﬀ

LED Colour cycle on / oﬀ

R red LEDs on / oﬀ

G green LEDs on / oﬀ

B blue LEDs on / oﬀ

Troubleshooting:

If the remote control

does not respond after

switching the light on, ﬁrst press the wall switch to

switch the light oﬀ. Then wait approx. 15–20 sec-

onds and activate the wall switch again.

If after switching on the luminaire again via the

remote control unit

the luminaire still does not

respond, check the batteries in the remote control

unit

Changing the bulb

CAUTION! RISK OF ELECTRIC SHOCK!

To replace the bulb, ﬁrst disconnect the light

from the mains circuit. To do so, remove the

fuse or switch oﬀ the circuit breaker in the fuse

box (0 position).

CAUTION HOT SURFACES! Allow the light

to cool completely.

Replace the bulb

only after it has fully cooled.

Remove the glass plate

by removing the

locating screws

CAUTION: Removing the locating screws will

also remove the washers

. Be careful

not to lose the washers.

Remove the glass plate

from the spacers

Unscrew the defective lamp

from the socket

with a ¼ turn to the left.

Use a clean, lint-free cloth when replacing the

lamp.

Only use LED lamps

with a GU10 base and

a maximum output of 3 W.

Carefully insert the new lamp into the socket

and secure with a ¼ turn to the right.

Place a rubber washer

on each locating

screw.

Push the locating screws through the glass

plate

Now place another rubber washer

each screw.

Secure the glass plate

to the light using the

locating screws.

Verify it is seated correctly.

Reinstall the fuse or switch on the circuit breaker.

Cleaning

CAUTION! RISK OF ELECTRIC SHOCK!

Disconnect the light from the mains circuit

before cleaning. To do so, remove the fuse or

switch oﬀ the circuit breaker in the fuse box

(0 position).

Only clean with a dry, lint-free cloth. Do not

use solvents, spirit or similar substances. They

could damage the light.

Allow the light to cool oﬀ completely.

The care of lights is limited to the surfaces.

Never allow moisture to enter terminal

compartments or conductive components.

Disposal

The package and packaging materials

consist entirely of environmentally friendly

materials. They can be disposed of at

your local recycling facility.

The symbol of the wheelie bin with the

line through it means that, in the European

Union, the product has to be disposed

of in a separate refuse collection. This applies to the

product and to all components bearing this symbol.

Do not dispose of products bearing this symbol in

your normal household waste, but instead they must

be taken for recycling to a collection site for electri-

cal and electronic appliances.

Recycling helps to reduce the consumption of raw

materials and protects the environment.

Batteries must not be disposed of as household

refuse! Advice is available from your local council.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Crivit 14103504L IAN 276356 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Crivit 14103504L IAN 276356

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info