Bedienungsanleitung Crivit HG04400 IAN 307528 (Seite 10 von 34) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

735887

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

10 GB/IE

Trampolines shall neither be installed over concrete, asphalt or any other

hard surface nor at proximity of other conﬂicting installations (e.g. pad-

dling pools, swings, slides, climbing frames);

Modiﬁcation of trampoline is not allowed.

The self-locking nuts

are for one-time use only and new nuts must

be used each time the product is assembled.

Particular caution – Risk of injury for children

Keep the packaging materials away from children. There is a risk of suf-

focation!

Parents and other supervisors should be aware of their responsibility as

situations and conduct may arise for which the exercising equipment was

not designed due to the playfulness and experimentation that is natural

in children.

If you allow your children to use the product you should take their mental

and physical development into account and, most importantly, their tem-

perament. Supervise the children and always instruct them on how to use

the product correctly.

Store the product out of the reach of children when not in use.

Risks from wear

The product may only be used when in perfect condition. Examine the

product for damage and wear before each use. The safety of the product

can only be guaranteed if it is examined regularly for damage and wear.

Discontinue use if damage is found.

Avoiding damage to property

Avoid contact with sharp, hot, pointed, or hazardous objects. Please

ensure that your exercising area is free of pointed objects.

Prior to assembling

To assemble this product all you need is the wrench and special spring

loading tool provided with this product.

During periods of non-use the product can be easily disassembled and

stored.

Please read the assembly instructions before beginning to assemble the

product.

Please refer to page for part descriptions and numbers. The assembly steps

use these descriptions and numbers as reference for your convenience.

Make sure that you have all parts listed. If you are missing any parts,

please contact the producer.

To prevent any injuries to your hands from pinch points during assembly,

please use gloves to protect your hands.

Moving the trampoline

In order to move the trampoline you should have as many helpers as the

trampoline has feet. Prior to lifting, all used fasteners (pegs, etc.) should

be removed. Caution! Due to the spring tension there is a possible risk that

the frame can be twisted as a result of uneven lifting. You and your helpers

should therefore be respectively positioned between two feet of the trampoline

and you should then all lift the trampoline at the same time. Lift the trampoline

oﬀ the ground slightly and keep it horizontal with the ﬂoor. To move the

trampoline in a diﬀerent way, disassemble it completely. To disassemble,

follow instructions for assembly backwards.

Assembly

Tools required:

1 x wrench

(included)

1 x screwdriver

(included)

1 x tool to tension the spring

(included)

Step 1 (Fig. A-G)

Please select all angled rods

, frame rods

, extension rods

and common sections

12a

12b

according to the products from the illustra-

tions. All parts with the sample part number are interchangeable, and to

connect the parts, simply slide section tubing that is smaller on one end

into adjacent section that has a larger opening.

Note: Frame rods`

punching holes upwards. While inserting the

extension rod

into the common section

12a

, ensure the screw holes of

the both parts align.

The bottom screw hole of extension rod

and screw hole of angled

rod

facing inward of the trampoline and then thread a self-tapping

screw

by screwdriver

The common section and extension rod are in alternately with hole

12a

and without hole

12b

on an angled rod

Step 2 (Fig. H-L)

When attaching springs

to the mat

, please invite another person

to help you with this portion of the assembly.

CAUTION! When attaching the springs

, the tube joints can become

pinch points since the product is tightening up.

Lay out the jump mat

with the printed side facing upwards in the product.

Position the circular hook of spring

on the eyelet of the jump mat

use the tool to tension the springs

to link up the round hook of spring

to the hole on the frame rods

Note: Refer to Fig. H for which hook of spring

to the mat

and

frame rod

Select an arbitrary point on the frame rods

(designate it as point ZERO).

Thereby, attach the ﬁrst spring

Count 15 holes from point ZERO in one direction. Thereby attach the

second spring

. Attach two further springs

at the same interval, so

that now four springs

are respectively attached in quarter-circle intervals.

Securely attach a further spring

in the middle of each quarter. If you

notice that you have skipped a hole and an eyelet, recount and remove

or attach any springs

required to maintain the rest of springs.

Step 3 (Fig. M-N)

Place the frame protection

on the assembled frame, so that the springs

and the frame are covered.

Please ensure that the frame protection covers all metal parts.

Place the elastic drawstrings so that every other string led over a common

section.

Fasten the drawstrings at the back of the common section. Knot the two

ends together.

Step 4 (Fig. O-Q)

Connect the lower enclosure pole

and upper enclosure pole

Put the pole cap

on the upper enclosure pole

and secure with

screw

, as Fig. O.

Mount the enclosure poles support with poles onto the trampoline leg

using the spacer

, screws

, nut

, cap nut

and washer

. Firm

the nuts using provided wrench

. Repeat until all the poles are set up.

Note: Use nut

on the upper hole of trampoline leg (hole of common

section

12a

), and use cap nut

on the lower hole (hole of extension

pole

Note: Nut

is one time use only. The nylon lock in the nut may dam-

age after use, and so it must be replaced for a re-assembly.

Step 5 (Fig. R-U)

Spread out Enclosure net

on the trampoline mat. Locate the panel

with the doorway and align the net as to where you would like to get in

and out of the product. Fasten the buckle of the enclosure net

on the

pole cap

Knot the rope

on an eyelet of the jump mat

. Then thread is as

shown alternately through the eyelet of the jump mat

and the enclo-

sure net

. Ensure the enclosure net

is completely well tired on all

eyelets of the jump met

IMPORTANT: All snap closures must be once again clamped securely

so that the enclosure net becomes taut. If the enclosure net is not taut, it

cannot complete this function as designed.

Crivit HG04400 IAN 307528 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info